Answered: Determine the moments of inertia bar-bx…

Determine the moments of inertia bar-bx af the area shown with respect to centraldal axis parallel to side AB Where: a-1,8 in b- 1.9 in C= 1.8 in al b. B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

150 mm 100 mg 200 mm PROBLEM 3.54 A single force P acts at C in a direction perpendicular to the handle BC of the crank shown. Determine the moment M, of P about the x-axis when 8 = 65°, knowing that M, = -15 N - m and M₂ = -36 N - m. Mx = 23.0 N-m
Calculate the reactions and draw the shear force and bending moment diagrams of the continuous beams or frames. E and I are constants, unless otherwise specified. Use the method of consistent distortions.
Use Area-Moment Method in solving the Problem.
6 m 3 m T1 2 m A T 4 m Ts B. 2. A mass of 6.12 kg is supported by the three wires as shown. AB and AC are in xz plane. Determine tensions T1, T2, and T3.
6. A force P of magnitude 330 lb acts on the frame shown at point E. (a) Determine the rectangular representation of Force Vector P. (b) Determine the moment of P about point O. (c) Determine the moment of P about a line joining points O and D. 7.5 in. 7.5 in. 10 in. E 0 P 30 in. H D B 10 in. x 10 in.
Problem 7.5 For the cantilever beam shown, it is required to determine the point where two bars theoretically can be cut off from the standpoint of the calculated moment strength, OM, of the beam. f, = 420 MPa and f.'= 21 MPa. 420 3@80 = 240 90 mm 90 mm 75 mm 10mmø stirups 4-28mm¢ W. 3.6 m 800 mm 725 mm 12. Calculate the moment the moment strength, ØM, , of the section. [in kN-m] 13. Calculate the maximum factored uniform load, w, the beam could support. [in kN/m] 14. Determine the distance from the free end where two bars theoretically can be cut off. [in m] 15. Determine the distance from the free end where two bars actually can be cut off. [in m] 16. Calculate the required development length, f dr at the support, if 90 hooked bars are used. [in mm]
2. Determine EI8 at point C of the beam figure shown below using Conjugate Beam method. 80 lb/ft RA RB 4 ft 2 ft
AND 306 mm 240 mm 240 mm 46.6 mm PROBLEM 3.9 The tailgate of a car is supported by the hydraulic lift BC. If the lift exerts a 125-N force directed along its center line on the ball and socket at B, determine the moment of the force about A.
Determine the moments of inertia of the Z-section about its centroidal xo- and yo-axes. 20 mm Answers: Ixo Iyo = = 175 mm IN i 130 mm- i Yo 20 mm -130 mm- 20 mm (106) mm4 (106) mm4
Use LRFD NSCP 2015 for all problems PROB. 1 Which of the given sections would you use on the column? A242 steel F, = 290 mPa. D = 875 kN SECT.1 SECT.2 L = 1450 kN Pipe Square Tubing Do So 5.6m So Outside S, = 380mm Do = 380mm t = 16mm t = 16mm
SITUATION 1: A T-beam is simply supported and is used to carry a uniform load of 20 kN/m. The beam is 4m long and has the following properties of the T-beam are as follows: bf=500mm; tf=100mm tw=200mm; dw=300mm PA 33. What is the moment of area of the beam with respect to its neutral axis? er a. 3.6 x 10° c. 5.8 x 10 b. 3.6 x 10° d. 5.8 x 10° as ad 34. What is the moment of inertia of the beam? a. 1.6 x 10° с. 1.8 х 105 b. 1.6 x 10° d. 1.8 x 10 42. the 35. What is the maximum horizontal shear stress on its neutral axis? a. 73.35 MPa C. 0.734 MPa on sa 92 b. 733.5 MPa d. 7.335 MPa 43. cab 36. What is average shear stress on the beam? b. 0.50 kPa d. 50 kPa а. 500 kPa c. 50 MPa 44. it st
The moment of the force F=180-lb about the point O in Cartesian vector form is. F 1 ft 4 ft 2 ft 4 ft. Select one: O a. Mo = 300j – 600k O b. Mo = -200j + 400k %3D %3D O c M, = -200j –- 400k O d. Mo = 200j + 400k