Use LRFD NSCP 2015 for all problemsPROB. 1 Which of the given sections would you use on the column?A242 steel F, = 290 mPa.D = 875 kNSECT.1SECT.2L = 1450 kNPipeSquare TubingDoSo5.6mSoOutside S, = 380mmDo= 380mmt = 16mmt = 16mm

Given : fy = 290 MPaA242 steel Dead Load, DL = 875 kNLive Load, LL = 1450 kN For the hollow circular…

PROB. 1 Which of the given sections would you use on the column? A242 steel F, = 290 mPa. D = 875 kN L = 1450 kN SECT. 1 SECT.2 Pipe Square Tubing Do So 5.6m So Outside S, = 380mm t = 16mm D, = 380mm %3D t = 16mm

PROB. 1 Which of the given sections would you use on the column? A242 steel F, = 290 mPa. D = 875 kN L = 1450 kN SECT. 1 SECT.2 Pipe Square Tubing Do So 5.6m So Outside S, = 380mm t = 16mm D, = 380mm %3D t = 16mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

WT12 x 38 Longitudinal welds Given: Properties of WT12 x 38: A, = 11.2 in? y = 3.0 in. b = 8.99in. Use A992 Steel: F, = 50 ksi F = 65 ksi LL = 3 DL %3D %3D tw = centroidal distance bf A. Governing Ultimate Tensile Capacity based on Yielding of gross section Round your answer to 0 decimal places.
SOLVE THIS PROBLEM USING THE SLOPE DEFLECTION EQUATIONS: The bearing type connection show is bolted by 4 – 22 mm diameter bolts (high strength bolts). The size of the plates is 300 mm x 12 mm. Fy 248 MPa, Fn = 330 MPa and Fu = 400 MPa. Determine the following: (1) Design strength of the connection based on strength of plates. (2) Design strength of the connection based on shear strength of bolts. =0.65. (3) Design strength of connection based on bearing strength of bolts on the 12 mm plate. =0.75 12 mm P. mm O. O 300 mm 40 80
Design the reinforcements of the given T beam below. bf=800mm bw=450mm tf=120mm d=600mm d'=80mm fc'=35MPa fy=350MPa USE NSCP 2015 A.Mu = 1300kN-m, As = B.Mu = 1600kN-m, As = mm2 _mm2, As' = mm2
Homework: A helica) cast steel with 3. helix angle has to tanmiz 35 KW at 1500 YPu. Gear has 24 teeth, 2 full depth. Tha Static Stress for Cast Steel maybe taken as 56 Mpa.. The width. of face may be talcen as 8 time) th module. Assum e : Cs =l, Ep=E= Ges=300 HPa , be =60 MPa, Calculate: WA, WNm, b, VR, = 200G Pa C=40.
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
3) will upvote anyone who will answer
a welded connection is in eqilibrium under the action of the four forces shown. Knowing that FA=8lbs and FB= 16lbs, determine the magnitudes of other two forces *3dec places all final
Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf-120mm d=550mm d'=80mm fc'=34MPa fy=415MPa USE NSCP 2015 A.Mu = 1300kN-m, As = mm2 B.Mu = 1800kN-m, As = mm2, As' = mm2
Q3-1 (Trusses), For the Figure shown below; 1 1. Find the forces in the members AB and AD of the truss and indicate whether it is in tension or 3m compression. 10KN 2. Read the following paragraph carefully then answer if it's TRUE or FALSE: The force in the member BC equal to zero? 3. Read the following paragraph carefully then CHOOSE THE CORRECT English Fried Safe 10KN 15 AN 3m 20 kN
Please correct answer otherwise dislike
Select all zero-force members in the truss shown below. Check the box for zero- force members 3 m 3 m 12 m, 8 @ 1.5 m DE O LK ЕР O HF O BC BM EF OM CD BN LO O DK FI O co
Two plates each with thickness t=16mm are bolted together with g-22 mm dia•bolts forming a lap connection.bolts spacing are as follows S1=40mm, S2=80mm,S3=100. Bolt hole dia=25 mm Fu=483Mpa Fy=345Mpa Solve the allowable strength and the ultimate strength in: 1. Yielding 2.rupture 3.shear 4.block shear