"OF2. Forces P and F acting along the bar shown in the figure, to maintain equilibrium of pin A. Determinethe value of P and F.DOA¹08 800 000 = AR BMX 6.5 = A0=33'00 m2 00 00k = g20088.840 = R9mG6mPC008 12m400#582000E = 0180 N300 N 0-0

2. Forces P and F acting along the bar shown in the figure, to maintain equilibrium of pin A. Determine the value of P and F. DOA 108 800 006 = AR B MX 6.88 = A 0=√73 '00 m2 00 00k = gl 2008 = 8.840 = R 9m 6m P C 008-12m 200 0E = 0 180 N 1400-58 300 N 0-0

2. Forces P and F acting along the bar shown in the figure, to maintain equilibrium of pin A. Determine the value of P and F. DOA 108 800 006 = AR B MX 6.88 = A 0=√73 '00 m2 00 00k = gl 2008 = 8.840 = R 9m 6m P C 008-12m 200 0E = 0 180 N 1400-58 300 N 0-0

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the elongation of wires AC and AB if the length of the wire is 106 mm and151 mm respectively. The cross sectional of both wire is 26 mm^2. Use E=20GPa
Your answer is partially correct. Replace the three forces shown by an equivalent force-couple system at point A. If the forces are replaced by a single resultant force, determine the distance d below point A to its line of action. 240 N 315 N Answers: M= R= i -345 i -120.60 Force-couple system at A. The force is positive if to the right, and the couple is positive if counterclockwise. Single resultant force. 210 N d = 349.65 670 mm 670 mm 670 mm mm N N.m
The wire AE is stretched between the corners A and E of a bent plate. Knowing that the tension in the wire is 420 N, determine magnitude of the moment about point C (Nm) of the force exerted by the wire on corner A. Round off only on the final answer expressed in 3 decimals. 033.png 90 mm. 120 mm 160 mm В 120 mm D E Add vour answwer
NOTE: WRONG SIGN IS WRONG. WRONG UNIT IS WRONG. 2P 5P A b a Draw your reference line at the leftmost part of the beam and determine the sum of all positive areas of moment diagrams. (Note: don't put units) Draw your reference line at the leftmost part of the beam and determine the sum of all negative areas of moment diagrams. (Note: don't put units)
6 m 3 m T1 2 m A T 4 m Ts B. 2. A mass of 6.12 kg is supported by the three wires as shown. AB and AC are in xz plane. Determine tensions T1, T2, and T3.
The influence line is for V40- = shear just left of 40'. A load of 0.5 kip/ft is placed in such a way to obtain the worst value of V40. Determine V40- in kips to two decimal places. Use the correct sign. -1 × -5.75 16 0.5 15 20 30 -1 ५०
Beam AB (A = left support, B = right support) is loaded with a concentrated load (P = 500 N) and a moment (100 N-m). Use a = 1 m. What is the value of the deviation of B relative to the tangent drawn at A? Round off to two decimal places.
PROBLEM 3. (30 PTS.) Use either the Portal Method or the Cantilever Method to approximate all the members' shear, moment and axial forces. Present your answer in the format presented by the SMA (for shear, moment and axial) in the figure below. 0.6P 8 M A P 3 M G D A 5 M 8m A H E B 5 M 8m A 1 F с 4m 4m P= 135kN
Please answer in complete solution and draw an fbd.Note: Please use the second picture as guide for the formulas. Thanks°
A two-span, continuous wood girder (E = 2,000 ksi) supports a roof patio structure (part (a) of the figure). A uniform load of intensity q acts on the girder, and each span is of length 8 ft. The girder is made up using two 2 x 8 wood members (part (b) of the figure). a q= 17.0 lb/ft -8 ft (a) B 8 ft 41 8 in. 2 in. 2 in. Section a-a (b) 000 8 in. Ignore the weight of the beam. Use the nominal dimensions of the beam in your calculations. (Solve by the method of superposition. The beam has constant flexural rigidity EI, unless otherwise stated.) (a) Find the reactions at A, B, and C. (Enter your answers in lb. Round your answer for Rg to at least one decimal place. Use the statics sign convention.) lb RA RB = lb RC lb
Determine the required magnitude of the couple moments M2 & M3 and so that the resultant couple moment of the system shown in Figure Q6 is 052 N.m? M2 45° M3 M = 300 N-m w] TOSHIBA F5 F6 F7 F8 F9 F10 F11 F12 INS SCROLL L &.
Using Virtual Work Method, calculate the horizontal displacement at joint B for the truss loaded as shown. The areas in mm2 are shown in parenthesis. E = 200 GPa for all members. В 200 KN (5000) (5000) (5000) D A. -(3500) Е (3500) 3 m 3 m (000s) (00SE)