Determine the moment of area of the given structural built-up section composed of a 8”x1” top flange, a 16”x1.5” bottom flange with a 1”x16” stem connecting the flanges. A 2- 3”x5”x1/2” angular bar supports the bottom flange.

Q: 4.Three members of a frame on a knot plate can be seen in the picture below. Determine the size and…

A:

Q: A 20 ft long simply supported beam has 15-inch outside diameter with 1-inch-thick circular section.…

A: Givensimply supported beamL=20ftD=15in=1.25ftt=1in=0.0833 ftq1=10 lb/ftP1=15lb

Q: The aluminium machine part shown below is subjected to a moment of M = 75 N.m. Determine the bending…

A: By the dimension given in figureshows that the figure is symmetric about th horizontal axis.that…

Q: Identify the centroid of the given semi circle if value of r = 20 as shown in figure.2 %3D R=rm

A: Given : Semi circle  radius = 20 m Centroid of semicircle : The point that is in the exact center…

Q: Determine the bending moment at point D if F₁ = 499 lb, F₂ = 263 lb, and F3 = 307 lb. -6 ft- F1 C I.…

A:

Q: Two vertical forces are applied to a simply supported beam with the cross-section shown. If L1 =1 m,…

A:

Q: ont of th.

A: →F = F= 300 N →F = F cos 20∘(-j)⏜ + 102.61(-i⏜)N         = 281.91(-j^)+102.61(i^) N →r= 200 mm i^ +…

Q: The cross sectional dimensions of a beam are shown. If the flange thickness, h, is 12.5 mm,…

A:

Q: Determine I'x of the shaded cross-section

A: Consider the diagram shown below for the given cross-section. The above section as a compound…

Q: Solve for the sum of moment of all forces clockwise direction is positive at point A, B, I & D.…

A: Given   Moments are given, we have to find the sum of moments. Take clockwise moments as positive…

Q: L1=4 in , L2=3 in, L3=1.5 in , h1=5 in , h2=6 in , f=7 lb , p= 45 lb. determine the proper angle in…

A:

Q: The handle of the press is subjected to a force of 20 lb. Due to internal gearing, this causes the…

A: Write the expression of the area and axial stress due to axial load acting on the system.

Q: mm. Determine the second moment of area of the cross section

A: To find Second moment of inertia of cross section

Q: The distance y from the back of the shorter leg to the neutral axis XX is

A:

Q: For the given section, (a) determine the moment of inertia about z & y-axes. (b) if the section is…

A:

Q: The hook is used to lift the force of P as shown. The section dimensions of a-a is given: P = 40 kN…

A: Given data: ◆ Load applied: P = 40 kN ◆ Inner radius of hook: c = 70 mm ◆ Parallel sides of section:…

Q: For the truss loaded as shown, determine the equation for the line of action of the stand-alone…

A:

Q: ind the monent ot ineta uf the gen amina about XX aes paing theugh its cenre shere bt 104 mn dt-3…

A: As given the T-section  The dimensions are:  b1=104 mm,d1=38 mm, b2=68 mm, d3=102 mm; ⇒x¯=∑ xiAi∑ Ai…

Q: The I-section has the dimensions (in mm) shown in the figure. Calculate the second moment of area…

A: given data D= 278 mm w = 181 mm find the moment of inertia about 'x-x axis.

Q: Handwritten solution required , including the free body diagram.

A: Step 1: Step 2: Step 3: Step 4:

Q: Q5: The forces FI-6 kN, F2- 5 kN, and F3-8 kN as shown in the Figure all of which act on point A of…

A: givenF1=6kN=6000NF2=5kN=5000NF3=8kN=8000N

Q: M = 8.5 kip-ft, find the magnitude of the bending stress at a point 3.14 in. above the centroid. The…

A: Bending moment is the summation of all the moments either to the left or to the right of the…

Q: PROBLEM 1: Consider the force system shown with the following forces and given angles F₁ = 85 KN…

A:

Q: Determine the moments about point (A ) due to the forces applied on the cantilevered beam.

A: The moment about point A is 30.39 kN-m

Q: A member having the dimensions shown is used to resist an internal bending moment of 30Nm. Determine…

A: Given The width of the beam is w=200 mm. The depth of the beam is d=150 mm. The value of bending…

Q: The I-section has the dimensions (in mm) shown in the figure. Calculate the second moment of area…

A:

Q: This shoulder bolt is composed of hot-rolled monel. The head of the shoulder bolt is a regular…

A:

Q: The beam shown in the figure is subjected to two forces. What would be the resultant moment about…

A: Given:-  To Find:-  Moment about point A (MA)  Solution:-  Sign convention :- Counterclockwise…

Q: The cross sectional dimensions of a beam are shown. If the flange thick the bottom edge of the…

A: Givenh=15.9mm

Q: The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a)…

A: The maximum tensile bending stress is

Q: An I-section is shown in the figure. All dimensions are in mm The centroidal axis X' is located as…

A: Given,

Q: Solve for the Following Bending moment equation for segment BC. a. 2000 lb(X) - 100 lb/ft (X…

A:

Q: P "Lx Answer: r1 F1 r2 A1 A1 = 69.0° F1 = 683.3 N rl = 22.3 m What is the moment due to F1 about…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.