Determine the maximum safe service live load that the beam can carry if the service dead load is 12 kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40 MPa and fy=415 MPa. Top bars are 6-32mm and bottom bars are 3-28 mm, center to center distance between the bar layers is 108mm. 7o mm 108 352 7o mm 300 mm

Determine the maximum safe service live load that the beam can carry if the service dead load is 12 kN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40 MPa and fy=415 MPa. Top bars are 6-32mm and bottom bars are 3-28 mm, center to center distance between the bar layers is 108mm. 7o mm 108 352 7o mm 300 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.8P

See similar textbooks

Related questions

Q: A composite beam cross section is made up of two rectangular strips. Each of (100x50) mm placed and…

A: A composite beam cross-section-To Find-The axial stress in the steel portion.

Q: Find: Calculate the following: Figure a. The gross moment of inertia, Ig b. The location of the…

A: Moment of Inertia:The moment of inertia is defined as the amount indicated by the object opposing…

Q: Use AISC Equation E3-2 or E3-3 and determine the nominal axial compressive strength for the…

A: The given figure is shown below:

Q: The strength of the rolled W section shown is increased by welding a channel and 220x40(mm) hollow…

Q: Civil Engineering For the stiffened panel shown, find the vertical and horizontal deflection of…

A: Given EA=2.5×106lbG=4×106 Psit=0.032 inl1=20 inl2=15 in Consider the figure of stiffened panel show…

Q: *4-36. The composite bar consists of a 20-mm-diameter A-36 steel segment AB and 50-mm-diameter red…

A: L1 = L3 = 250 mmL2 = 500 mmA1 = A3 = π4×502A2 = π4×202Esteel = 200×109 Pa & Ebrass = 101×109 Pa…

Q: 2. The column shown in the figure is reinforced with 415Mpa and f'c = 27Mpa a. Determine the nominal…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

Determine the maximum safe service live load that the beam can carry if the service
dead load is 12 kN/m including the beam weight and based on the capacity of the beam
section shown. Use fc'=40 MPa and fy=415 MPa. Top bars are 6-32mm and bottom
bars are 3-28 mm, center to center distance between the bar layers is 108mm.
7o mm
108
352
7o mm
300 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
using Figure 5-27, what is the advantage of the suspended type magnet over the other two types of magnets?
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.