Determine the maximum reaction at support B, the maximum shear at point C and the maximum positive moment that can be developed at point C on the beam shown due to: "a single concentrate live load of 8000N "a uniform live load of 3000 N/m (applied on specific area: say positive area or negative area only) "a beam weight (dead load) of 1000 N/m (applied on the entire beam) A C B 4 m 5 m 4 m

Determine the maximum reaction at support B, the maximum shear at point C and the maximum positive moment that can be developed at point C on the beam shown due to: "a single concentrate live load of 8000N "a uniform live load of 3000 N/m (applied on specific area: say positive area or negative area only) "a beam weight (dead load) of 1000 N/m (applied on the entire beam) A C B 4 m 5 m 4 m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

Please can you you supply me with the shear force diagram for question 3
stresses in beams
The flexibility matrix for the beam shown in the figure is: 2 EI 1 3 2 EI 2EI 3ΕΙ 2ΕΙ (b) -L2 L (a) 2EI 3EI 2E1 ΕΙ 4E1 -6ΕΙ 7- 3EI 2EI Cc) (d) -6EI 12EI 2ΕΙ ΕΙ
need fast
i need the answer quickly i need all the steps, i need the answer in Handwritten.
Quizs- Replace the loading system by an equial ent resultant force and Couple moment acting at Point o. fi=l00 N Mc:75 Nm 0:3m 200 0-5 m 0.4m
Axial deformation
Subject: Date: 10KN 4 KN /m 6 m -3m K-Iim-* 3m 3m Figure I Figure 1 shows the Simply supported beam AB-Petermine a) support reaction a+ A b) Support reaction at
Equilibrium 3d analysis
Fig. P3.48 0.4 m 0.1 m B 0.3m 150 N-m 60 Nm Hibbeler F5-55. The assembly is made of A-36 steel and consists of a solid rod 20 mm in diameter fixed to the inside of a tube using a rigid disk at B. Determine the angle of twist at C. The tube has an outer diameter of 40 mm and wall thickness of 5 mm.
STRUCTURAL PART Interactive Question Choose the correct answer of the bending moment diagram of the Frame Below (Ignore Self weight) (A) B A Prepared By: ENG. MODAR HAJYOUNES Prepared By: ENG. SULAIMAN WARDAH C Prepared By :Eng. Moda Hajyounes B -A Another Unstable D E
B 300 mm ↑ 15 mm 70 KN 70 KN 20 mm 500 mm Steel Aluminum AMIN ATTIV 70 kN 70 KN + Rc A steel rod (20 mm diameter) 500 mm long is connected to two parallel aluminum rods (15 mm diameter) each 300 mm long via a rigid plate as shown. Two 70 kN loads at applied at the end of each aluminum rod. The structure is fixed at both ends resulting in a statically indeterminate system that can be treated as the superposition of two determinate systems as presented above. Note that Rc is the reaction at C. Assume Esteel = 200 GPa and Ealuminum = 70 GPa. a) Determine the reaction force at C, Rc b) Determine the reaction force at A and B and the normal stress in the steel and aluminum rods c) Which rods are in tension and which are in compression?