Determine the maximum bending moment for the beam shown below. Use a = 9 ft, b = 13 ft, c = 7 ft, and w = 15 kips/ft. The reaction forces for this beam are Ay = 90.8 kips and Dy 104.2 kips. 1. D. Answer: kip-ft Mmax = eTextbook and Media Submit Answer Attempts: 0 of 3 used Save for Leter Using multiple attempts will impact your score, 5% score reduction after attempt 1

Determine the maximum bending moment for the beam shown below. Use a = 9 ft, b = 13 ft, c = 7 ft, and w = 15 kips/ft. The reaction forces for this beam are Ay = 90.8 kips and Dy 104.2 kips. 1. D. Answer: kip-ft Mmax = eTextbook and Media Submit Answer Attempts: 0 of 3 used Save for Leter Using multiple attempts will impact your score, 5% score reduction after attempt 1

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; = 1990 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume MA= 250 kip-ft, P= 14 kips, LAB = 4.1 ft, LBc = 6.2 ft. MA LAB LBC Answer: in. (a) VA- in. (b) VB - 4. Submi Attempts: 0 of 1 used Save for Later
PROBLEM 4 - A solid shaft given below is made from two segments: AC has a diameter of 15 mm and CB has a diameter of 10 mm. Determine the support reaction at point B and clearly statie its direction if it the shaft is fixed at points A and B and is subject to a torque 7' at point D. Take the shear modulus as 50 GPa. Write your final answer in the textbox below. Hint: J0.5ne, where e is the radius. 15 10 mm D. B. T 20 Nm 1m 0.5 m 2 m Wall
Based on the following illustration, solve the following questions: IP-15 KN w=5 kN/m B 5m 5m 5m The magnitude of the maximum bending moment (kN-m) in the beam is most nearly. Select the correct response: 14 63 25 6.3
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1900 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume Ma = 190 kip-ft, P= 19 kips, LAB = 3.0 ft, Lgc = 4.5 ft. MA LAB LBC Answer: (a) VA= in. (b) vg = in.
Given this simply supported beam, what is the vertical reaction at end B? The value of a is 3m, the value of b is 5m, and the value of w is 3kN/m. (Please express your answer in kN to two decimal places, but do not include “kN” in the answer below.)
The hoisting arrangement for lifting a large pipe is shown in the figure SD-05Q002. The spreader is a steel tubular section with outer diameter 75 mm and inner diameter 60 mm. Its length is 2.5 m and its modulus of elasticity is 200 GPa. What is the maximum weight of pipe, in kN, that can be lifted based on the following conditions? (Assume pinned conditions at the ends of the spreader.) Use: V = 3 H = 4 Problem 7 Based upon a factor of safety of 2.0 with respect to Euler buckling of the spreader. a. 205 b. 434 c. 355 d. 217 Problem 8 Based upon the allowable stress design if Fy = 248 MPa. a. 205 b. 434 c. 355 d. 217 Problem 9 Based upon the critical stress. a. 205 b. 434 c. 355 d. 217
The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa; I = 370 x 106 mm*). For the loading shown, determine the beam deflection vc at point C. Assume P = 56 kN, w = 22 kN/m, Lag = Lsc= 2.9 m, Lco = 2.9 m. LAB LBC LCD Answer: Vc= mm.
Consider the timber beam shown below. The beam is made out of southern yellow pine, with an allowable bending stress of ?all= 2700 psi. The modulus of elasticity is E = 2,400 ksi. The maximum allowable deflection in the beam is 0.25 inches. A 1.5 kip/ft 6 ft 4 in. h B (a) What are the boundary conditions for this beam? (b) Determine the equation for the moment diagram using statics. (c) Determine the depth of the beam necessary to meet the allowable bending stress requirement.
hi im stuck in this please help me out A wooden beam is loaded by a concentrated load ?P = 5000 N and supported by boundary conditions as shown in Figure Q5(a). The cross-section of the beam is shown in Figure Q5(b). Given that ???LAB = 3000 mm, ???LBC = 2000 mm, ?0B0=10 mm, ?1B1 = 30 mm, and ?H = 240 mm, ℎ0h0=200 mm, ℎ1h1=20 mm, determine the following quantities below: last two sub parts of question didnt fit in so i will type here- theres no question d e) Determine the maximum magnitude of shear force and bending moment, neglecting the sign. The maximum magnitude of internal shear force, positive value: N The maximum magnitude of internal bending moment, positive value: N*mm f) Determine the magnitude of the maximum bending stress in the beam, neglecting the sign. Maximum bending stress, positive value: MPa
Consider the free body diagram for the truss system below. Taking moment about point A, determine reaction force R, B 80 kN A MATHalino.com MATHalino.com AH 1 m 1 m 1m 50 kN Ay Ro 0.75 m
Consider a 3 metre long uniform beam with flexural rigidity of 100 kNm². The beam is supported with a fixed (clamped) support on the left, and a roller support 1 metre from the right hand side. 3m 2m A 1kN/m point load is applied 1 metre from the left hand side. If we find the deflection for this beam, using the boundary conditions for the fixed (clamped) end and for the roller support, we get the equation. y(z) 9600 ((16³-48x² +48r - 16) H(r− 1) - 112³ +18r²) (you do not need to calculate this yourself, but you may verify it if you wish) Have Desmos (or any other computer graphing system you like) draw a picture of the beam under load. Make sure the picture is accurate, and is zoomed appropriately to see the actual bends in the curve. What is wrong with the deflection function to the right of the roller support? b) Solve the deflection for this beam in two parts, as if there were two separate beams: 3m Om 2m 2m For the roller support use the following boundary conditions: y (2)= 0 and…
Part A The beam is subjected to a uniform dead load of 1.4 kN/m and a single live load of F = 35 kN . Assume A is a pin, and B is a roller. Follow the sign convention. (Figure 1) Determine the maximum bending moment created by these loads at C. Express your answer to three significant figures and include the appropriate units. (Mc)max = 130 kN-m Submit Previous Answers Correct Correct answer is shown. Your answer 130.2 kN.m was either rounded differently or required for this part. Part B Determine the maximum positive shear at C. Express your answer to three significant figures and include the appropriate units. Figure 1 of 1 (Vc)max = Value Units 6 m 6 m Submit Previous Answers Request Answer X Incorrect; Try Again; 3 attempts remaining