Determine the magnitudes of FA and Fg so that the resultant force passes through point O of the column. Suppose that a = 100 mm, b= 150 mm, c = 650 mm, and d = 700 mm. (Figure 1) gure < 1 of 1 > FB 6 kN 750 mm 8 kN FA 600 mm

Q: The strength of solid shaft is of hollow shaft of same weight. the strength

A: The torque transmitted by the hollow shaft is more than a solid shaft for the same weight and…

Q: Q-6: Blocks A and B are identical with each weight of W. If the coefficient of static friction…

A:

Q: dy = m y2 dx

A:

Q: Write F if True and T if False. Golf countries are rich because of their oil deposits

A: It is true(F) that gulf countries are rich because of their oil deposits.

Q: When pressure increases, the temperature increases. Select one: True False

A: Pressure: force acting per unit area Temperature : it is actually a physical quantity that expresses…

Q: part1 and part 2 are correct

A: Process 3-4s : Isentropic expansion process.Process 3-4a : Actual expansion process.Process 4a-1 :…

Q: Double acting cylinder cannot be used as a single acting cylinder. Select one: O True O False

A: Single Acting cylinder as it were expands by weight from a pump and after that withdraws by the…

Q: nd Steel, respectively. Given the modulus of elasticity of materials are Ealuminium = 69 G %3D…

A:

Q: Q 3/ Give the names of the components to the parts in the vehicles According to the figures. Manual…

A: Given figure shows the schematic of the manual transmission system.

Q: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

A: The figure shows a cylindrical shell very long, of length L, very internal radius large r1, outer…

Q: Finding the y centriod.

A: Given data, the I section is given with dimensionFind outthe centroid along the y-axis

Q: What is the precision measurement of 1 7/8 inch

A: PRECISION IS DEGREE TO WHICH REPEATED MEASUREMENTS UNDER THE SAME CONDITIONS SHOW THE SAME RESULTS.

Q: A pneumatic system operating at 85 psi comprises a series of pneumatic actuators which consume 2.4…

A: Original CFM = 2.4 CFMOriginal pressure= 85 psiNew pressure= 120 psiAtmospheric pressure= 14.7 psi

Q: 1. The built-up beam pictured on the right is subjected to an internal moment of M = 75 kNm. a) At…

A: *The internal moment acting on the structure is M=75 kNm. *The total length of the T section is…

Q: m. nd Find the components of the equivalent force. Express the re Express the z, y, and z components…

A: The position vectors are-

Q: The force developed in the brake cylinder is 2.74 KN and the diameter of the cylinder is 4.5 cm. If…

A: Option d is correct

Q: Label all forces that act on the metal

A: A piece of metal is submerged in the liquid and one end of the metal piece is fixed with a string.…

Q: The piston rings are used to act as a seal between the piston and cylinder head a. FALSE b. TRUE

A: We have to determine true /false of The piston rings are used to act as a seal between the piston…

Q: When the diameter of cylinder is very small compared to its length, it can be treated as an…

A: As per given question  When the diameter of cylinder is very small compared to its length, it can be…

Q: how did you find d1 and d2

A: This question is based on the concept of polar radius.

Q: If a force doubled, impulse will triple. True or false

A:

Q: Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium, Brass and Steel,…

A:

Q: -As shown in the Figure 2, please to draw the axial force diagram of the roa. 20 kN Figure 2 10 kN…

A:

Q: 100 mm 100 mm 10 mm 10 mm. 200 mm 100 mm f 10 mm I II

A: For the selection of sections, we have to calculate the maximum bending stress in the beam. From the…

Q: Determine the x, y, z components of reaction at the thrust bearing D 0 = 0°.

A:

Q: What is the meaning of + S.F, -S.F, +B.M and ?- B.M

A: There are sign convention for shear force and bending moment.  The shear force at a cross-section is…

Q: QUESTION 2 A single-cylinder, 4-stroke, 3-liter gasoline engine operates at 791 rpm and a…

A:

Q: I need these three parts answered pertaining to the print provided. If you can not answer all three…

A: The term, Orthogonal, describes the relationship of the axis of the ½” NPT pipe plug with the main…

Q: Z is incorrect

A:

Q: if the bullet that hit the cashier made a bullet hole that was 3 mm wide and 8 mm long, white was…

A: Given data:

Q: Which is figure depicts the ideal diesel cycle processes? Caipr rejeto. V3=Uz B. C S.

A: Ideal diesel cycle is combustion process in IC engine which comprises the four process to complete a…

Q: Negative force and Displacement will cause compression andcontraction? True or False?

A: The negative force causes compression is a true statement. In the end, the resultant forces must be…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: A piece of 3 ⁄ 4-inch 5052 aluminum alloy tubing with a wall thickness of 0.070-inch has an inside…

A: Given, Wall thickness, t=0.07 inch

Q: hat is the increment of the 3 cylinders?

A: When we increase the number of cylinders in a vehicle, the power and performance of the engine both…

Q: - 2- 45 100lbs/ft 300lb 30 200lbs

A:

Q: Read the following millimetric vernier caliper setting 005mm Answer with units:

A: Vernier caliper reading = reading of main scale + reading of other scale (where the two lines are…

Q: By and bx are labeled wrong

A:

Q: True or False? All rectangular x-sections less than 12-inch in width and less than 0.23-inch in…

A: The minimum width for the all rectangular section to be known as strip is 12 inches while the…

Q: What is the thickness of steel?

A: To find thickness of steel.

Project Management Techniques

The guideways or the roadways that are undertaken to perform a project efficiently and all the tools required to accomplish the task are the general outlines for project management techniques.