Determine the force Prequired to force the 17° wedge under the 75-kg uniform crate which rests against the small stop at A. The coefficient of friction for all surfaces is 0.33. 1.7 m 0.7 m 75 kg 17° A P 17°

Q: Matt my machinist friend from Germany, says he can easily hold a tenth of a millimeter in his mill.…

A: Different units have been devised by Scientists and Researchers to facilitate measurements such as…

Q: What is Line J? ARROWHEAD .35mm 7.0- HIDDEN LINE 3mm K 01 5 0,5- 3. NOTE 5mm H. E. ABCO

A: Answer: The line "J" is called "section line". Therefore, the correct option is (C).

Q: Make the part program using CNC code.        Tool Dia. = 6 mm        depth of cut 3.0 mm…

A: Tool Dia. = D =6 mm depth of cut = d= 3 mm (Use G90 code)  To find: Make the part program using CNC…

Q: Sketch the figure using AutoCAD and hatch the lines with colours . mention the dimesions as shown in…

A:

Q: 27. You have the following compound machine. 60 teeth 40 teeth 20 teeth a. What is the speed of Gear…

A:

Q: Write the number of limbs, determine the degrees of freedom and draw the kinematic chain.  b)…

A: As valve engine is given where we are to find 1st number of links and number of higher joints and…

Q: what is the displacement?

A:

Q: draw the left side

A:

Q: able to draw the sequence chart?

A: you are asking about Sequence chart.

Q: Question Completion In the figure below, which of the following represents the dedendum? zeta gamma…

A: Circular pitch is the distance measured from a point on one tooth to the corresponding point on the…

Q: Find the distance traveled by the slider if connecting rod is 10 inches, cranks is 30 deg (past top…

A:

Q: Convert the octal number 23228 to its hexadecimal number equivalent, (base-8 to base-16).

A: Steps of Conversion: The simplest way is to convert the octal number into a decimal, then the…

Q: why is the angle 26.56 and then you use 22.56

A:

Q: Construct a Main Schedule of the machine tool of your choice?

A: The machine tool should have preventive maintenance . it is an essential thing for the properly and…

Q: Which tools that can be used to :2 draw the following shape in .AutoCAD Polygon, Hatch line,…

A: Find tools used in AutoCAD to draw the following drawing.

Q: EX7: write a program read any vector and print the odd order only?

A: Required: Program to read vector and print item ad odd order.   all the code with code screenshot…

Q: raw kinematic diagram of the drawing mechanism. etermine degrees-of-freedom of the drawing…

A:

Q: A) Draw the two limiting positions of the following crank-slider mechanism. Indicate all known sizes…

A: Given:To find:(a) Draw the two limiting positions.(b) Determine the piston stroke.

Q: Please do #5

A: Given AB+CD=X

Q: 4. Design 4-bit left and right rotators. Sketch a schematic of your design.

A:

Q: L t C Determine the moments at fixed ends 'a' and 'd' ?

A:

Q: is 60 left or right?

A: The horizontal reaction at A: 60 kN (Right)......(Option D)

Q: Write the procedure of slotting operation in ten steps.

A: Slotter Machine  A Slotter machine is described as a machine tool utilized for eliminating…

Q: OFFSET command use to draw object parallel to selected object by determine radius distance point…

A: Computer-aided drawing is the way to draw the various views of the component. In the orthogonal…

Q: A meter stick balances horizontally on a knife-edge at the 50.0 cm mark. With two 3.17 g coins…

A:

Q: What's the answer for Q4 D and E with working out and answer as you already answered A-C

A: a) Write the expression for the specific speed. Here, N represents the rotational speed of the…

Q: 9. Please list the basic procedure of calculating the X- and Y-coordinates of the tool centerline…

A:

Q: Analytically determine the maximum linear displacement of the cutting blade .75 S0 crank blade Your…

A:

Q: Determine the following for point C on the slide if the angle theta measures 45 degrees and the BC…

A:

Q: In a slider crank mechanism (schematic shown the figure), the crank rotates at 60 revolutions p…

A:

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: Which option is wrong?   a)The center head is used to find the center of a square on surface of…

A: Which option is wrong ?

Q: 4. Write an APT NC Part program (milling and drilling) for the following work part. The outline of…

A:

Q: Up milling operation, the work is feed in the same direction the rotation of the cutter. Select one:…

A: Given :-  Up milling operation, the work is feed in the same direction the rotation of the cutter.…

Q: In the figure below, Which of the following represent the dedendum

A:

Q: how to calculate cylunder taper and out of round

A: Cylinder out of Round is the difference of diameter when measured parallel to the crankshaft and…

Q: Give the horizontal and vertical distances from the upper left corner of this part to the center of…

A: The depth and dimension for the slot is 0.243 and for chamfer 0.089 depth. Hole A X…

Q: question: The degrees of freedom of the calculation package in the figure?

A:

Q: SHAFT KEY

A:

Q: In a milling machine the distance the workpiece advances under the cutter is known as Select one: a…

A: Option d is correct.

Q: Disadvantage of taper turning by taper turning attachment method is that only limited taper angles…

A:

Q: Which tools that can be used to :2 draw the following shape in .AutoCAD J Polygon, Hatch line,…

A:

Q: Draw the and B A.F.D&S.F.D& B.M.D (KN.M

A: To draw axial ,shear and bending moment diagram

Q: When it comes to finding the moment arm, you must use the distance of the line from the pivot to the…

A: Explanation When it comes to finding the moment arm, you must use the distance of the line from the…