Determine the design shear strength of the given shape, using Fy=50 ksi. Blank 1W14x53...A =15.60in.^2d =13.900in.tw =0.370in.bf =8.060in.tf =0.660in.T=10-7/8in.k =1.2500in.k1 =1.0000in.gage =5-1/2in.rt =2.150in.d/Af =2.62Ix =Sx =541.00in. ^477.80in.^3rx =5.890in.ly =Sy =57.70in.^414.30in.^31.920ry =Zx =in.87.10in.43Zy =22.00in.43J =Cw =1.94in.142540in. ^6a =58.22in.Wno =26.70in.^2Sw =35.50in.^4Qf =16.80in.43Qw =42.60in.43

Answered: Image /qna-images/answer/46532e04-90fd-4bb2-ac55-382623a4329a.jpg

Answered: Determine the design shear strength of…

Engineering

Civil Engineering

Determine the design shear strength of the given shape, using

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The Load P = 2600 lb is applied on a five bolt truss. If the average shear stress in the bolts must…

A: Given: The 5 bolts structure,The load given is 2600 lb,The total number of bolts is 5,The average…

Q: write the advantage and disadvantage of stiffness method and flexibility method

A: Answer The flexibility method is also known as the Force method. The stiffness method is also known…

Q: DETERMINE THE LARGEST LOADP THAT CAN BE APPLIED TO THE BARS OF THE LAP JOINT SHOWN IN THE FIGURE.…

Q: A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the…

A: Given ; Dia of lag screws = 22 mm width of steel bar = 69 mm thickness = 8mm the yield strength =…

Q: I section steel profile is not symmetrical as shown. If the tensile stress on the upper side of the…

Q: A steel bar is attached to a wood support beam with four 22 mm diameter lag screws, as shown in the…

A: Given Diameter of screw, d = 22 mm Number of screws, n = 4 Width of steel bar, b = 69 mm Thickness…

Q: A PROB. 1.8-12 a 2P B (a) D XII Gusset plate Rivet (b) Section

Q: 0,3in 0.4in2 3P 2P + C. Find the albwable säfe p if the stresses in the bar are the following: AB 50…

Q: For tension members, is it always true that the effective area is less than the gross area (e., Ae <…

A: The tension members are the members which carry axial tensile load leading to elongation. Such…

Q: Which among the formulas below can be used to compute the combined stress at the bottom fiber of a…

A: sign convention compression =positive (+) tension= negative (-)

Q: Consider the truss shown. Determine the force acting on member CF, EF, and FG. B A D 3 m E 4 m 45 kN…

Q: Answer this using method of joints. Show your clear, detailed, and whole solution. Don’t mind the…

Q: Three plates are welded together to form the section shown. Dimensions of the cross section areb-4.7…

Q: What is the characteristic strength of a mild steel reinforcement bar? Select one: O a. 415 N b. 415…

A: A multiple choice questions have been given and it has been asked to choose select suitable answer.…

Q: Determine the force in each member of the truss shown. Indicate whether the members are in tension…

Q: 3.50 m P-12 KN P= 24 KN 2.50 2.50 P-BC KN P=30KN P=30KN 2.50 | 2.50 | 2.50 20.00 m P=24 KN P-12KN…

A: To compute:Member forces

Q: the

A: A device for measuring corneal thickness that is installed on a slit-lamp is known as pachometer. It…

Q: ction is welded to a noc owing figure shows. De equired thickness, roun

Q: Q2:If allowable stresses are at = max. value of W. W 2m 8m 165MPa, oc = 100MPa t = 70MPa determine…

Q: 8 kips 4 kips 4 kips d, =2" 15 kips 15 kips -d2 =1.5" !0 kips 20 kips d, =3" A Fig. for Problem #2

A: There are 3 bars AB, BC, CDThe forces on those bars are also given.Diameter of bar CD, d1 = 2…

Q: 1. Determine bar forces in the truss beldw 30 KN 30 KN 30 N 2m

Q: Fig3 6cn Į 25 3 cm Tom R 5cm Icm 11 cm

Q: Determine the maximum permissible value of T provided the allowable shearing stresses in brass and…

A: Given:- ζball = 70 MPaζsall = 110 MPaGs = 80 GPaGb = 40 GPadi = d = 70 mm, d0 = 90 mm…

Q: The given plate below with width of 200 mm and thickness of 16 mm is to be connected to two plates…

A: A riveted steel link is produced by drilling holes through the thickness of both components, passing…

Q: PN 50° 50 75 50 50 75 50 75 50 50 125

Q: By inspection, determine the zero-force members in each truss. Identify the zero-force member by…

A: As per our guidelines we are suppos d to answer first three subparts. Kindly repost other part as…

Q: 2. A butt joint is fastened by four %4" diameter bolts. If the joint transfers a tensile force P of…

A: Objective: To compute the average shearing stress in the bolts and the bearing stress between the…

Q: (i) Find the shape factor for the tee section as shown in figure. 20 mm 20 mm 120 mm 200 mm

A: Given Data Find the shape factor.

Q: For the truss shown, Fi=240KN and F2=720KN. Determine the forces in the rod BD and the rod BE (unit…

Q: The vertical force P acts on the top of the post. Please determine the distance d at which the load…

Q: P 2 m W = X N %3D F1m- 4 = 0,3 - 1m-| Determine the normal force between the crate and the surface…

A: To find the normal force (N) and force (P)-

Q: Calculate the maximum shear stress in the cross section shown if the total shear load applied is…

Q: Fig3 6c.n ㅍ 25 3 um Tom 7 5cm Icm I 1cm

Q: Determine the maxinum tensile stress and compressive stress for the beam with the given cross…

A: Max moment occurs at Left supportMmax=-10004=-4000lb-ft so,

Q: For the truss shown, calculate the stress in member BD. The cross-sectional area of each member is…

A: We have to find out the stress in member BD

Question

Determine the design shear strength of the given shape, using Fy=50 ksi. Blank 1
W14x53
...
A =
15.60
in.^2
d =
13.900
in.
tw =
0.370
in.
bf =
8.060
in.
tf =
0.660
in.
T=
10-7/8
in.
k =
1.2500
in.
k1 =
1.0000
in.
gage =
5-1/2
in.
rt =
2.150
in.
d/Af =
2.62
Ix =
Sx =
541.00
in. ^4
77.80
in.^3
rx =
5.890
in.
ly =
Sy =
57.70
in.^4
14.30
in.^3
1.920
ry =
Zx =
in.
87.10
in.43
Zy =
22.00
in.43
J =
Cw =
1.94
in.14
2540
in. ^6
a =
58.22
in.
Wno =
26.70
in.^2
Sw =
35.50
in.^4
Qf =
16.80
in.43
Qw =
42.60
in.43

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A built-up shape is shown in Figure 1, a) determine the elastic section modulus; b) determine the plastic section modulus; c) determine the shape factor; and d) what is the LRFD design shear strength of the shape if Fy = 250 MPa, h = T = 274 mm? K Figure 1 250 mm 50 mm 200 mm 50 mm 300 mm 50 mm
show nicely the solutions
1. Refer to the sketch below. a. What type of joint is shown? b. What type of weld is shown? C. Is the weld in shear or normal stress? d. Calculate the magnitude of stress in the weld. K /P= 50 Kip /P = 50 Kip 10" I 1/4"
List the elements of {xIx is a rolled steel section}.
6
Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
3. Determine maximum strength P for the bracket connection in the figure. ST37 steel is used for the connection, F = 2400kg /cm,F, = 3700kg /cm %3D %3D IPE200 15 cm P=? PL 250x150x15 mm te 7 mm, L=250 mm