Determine the coefficient of permeability of the soil. For a falling- head permeability test, the following are given 6324 Length of the specimen 115.5 mm Diameter of soil specimen = 104.7 mm Diameter of the stand pipe = 15 mm %3D %3D %3D Head difference at time t=0 is 1360 mm Head difference at time t=78600 sec is 820 mm

Determine the coefficient of permeability of the soil. For a falling- head permeability test, the following are given 6324 Length of the specimen 115.5 mm Diameter of soil specimen = 104.7 mm Diameter of the stand pipe = 15 mm %3D %3D %3D Head difference at time t=0 is 1360 mm Head difference at time t=78600 sec is 820 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

13 For a constant laboratory permeability test on a fine sand, the following data are given: Length of specimen: 19 cm. Diameter of specimen: 99 mm. Constant head difference: 51 cm. Volume of water collected in 4.86 min.: 427 cc Void ratio of the soil specimen: 0.51 Determine the seepage velocity in m/min. Round off to four decimal places.
The results of a laboratory consolidation test on a clay specimen are the following. Pressure, ir (lb/ft²) 500 1.000 2.000 4.000 8,000 16.000 Total height of specimen at end of consolidation (in.) 0.6947 0.6850 0.6705 0.6520 0.6358 0.6252 Given the initial height of specimen = 0.748 in.. G specimen = 95.2 g. and area of specimen = 4.91 in.²: a. Plot the e-log or curve = 2.68. mass of dry b. Determine the preconsolidation pressure c. Calculate the compression index, C.
The laboratory consolidation test is conducted on a clay sample. The following data results were obtained P1 =55 kPa P2 = 130 kPa e1= 0.95 e2= 0.80 Thickness of the sample of clay= 35mm Time for 50% consolidation = 3.0 min Tv= 0.197 a. Find the coefficient of volume compressibility b. Determine the coefficient of consolidation if a sample of clay was drained on both sides c. Compute the hydraulic conductivity of the clay
A series of direct shear tests has been performed on a dense well-graded sand. All tests were performed on 3.00-in. diameter, 1.25 in. tall cylindrical samples, and were run slowly enough to produce drained conditions. The results of these tests are summarized in the following table: Test Number Normal Load (lb) Shear Load at Failure (lb) 1 100 84 2 200 159 3 400 319 Assuming the shear area remains constant during the test, determine the effective cohesion and effective friction angle from these test results. What values of these parameters would you expect? Are the test results consistent with your expectations? What values would you use for design?
Sand cone equipment is used to perform a field density on compacted earth fill. Sand is used in the cone and is known to have a bulk density of 15 kN/m3. The wet weight of soil sample from the test hole is 20.601 N. The dry weight of soil sample is 17.926 N. The weight of the sand in the sand cone to fill the test hole is 16.053 N. Determine the in-place dry density in kN/m3 of the tested soil.
The data from a falling-head test on a silty clay are: Cross sectional area of soil = 1000 mm^2 Length of soil sample = 200 mm Area of stand pipe = 40 mm^2 Head difference at time t = 0 is 500 mm Head difference at time t = 3 min is 300 mm a) Determine the hydraulic conductivity of the soil in cm/sec. b) What is the head difference at time t = 100 sec in mm
Consolidation test is conducted to QI determine the consolidation properties of the soil. Table 1. Test Result The dial gauge reading after each load increment (24 hours) is given in the table. Initial sample thickness, Ho = 20 mm, Initial void ratio, e, = 0.9. Determine the following: Construct the compressibility curve and predict the past maximum stress/pressure (preconsolidation stress/pressure) (kPa) Dial gauge reading after 24 Vertical stress (kPa) hours (mm) 22.50 %3D 40 22.41 80 22.15 160 21.51 320 20.25 640 18.45
For a falling head permeability test, the following are given: length of specimen is 360 mm, area of specimen is 70 cm2 , and hydraulic conductivity of soil specimen is 0.165 cm/min. what should be the area of the stand pipe for the head to drop from 700cm to 360cm in 7 mins? compute the seepage velocity under the test condition if the soil specimen has a void ratio of 0.55 in cm/sec compute the head difference at time equal to 5 minutes?
Q: The constant-head permeability test arrangement in a two-layered soil has been arranged as shown in Figure. During the test, it was seen that when a constant head of h₁= 220 mm was maintained, the magnitude of h2 was 70 n If ki is 0.005 cm/sec, determine the value of k2. (given that H₁-120 mm and H₂= 160 mm). h₁ Soil 1 (ky) ►1 Soil 2 (k₂) Water supply T h TT H₁ H₂ ©ⒸCengage Learning 2014
Q # 1. Organic soils are typically characterized by high void ratio, low specific gravity, and high compressibility. Following are the results of a consolidation test on a sample of organic soil. Pressure, o (kN/m2) Change in dial reading, AH (mm) 0.284 12 0.150 24 0.315 48 0.564 100 0.823 200 2.25 400 5.34 Given that the initial height of the specimen = 20.6 mm, mass of dry specimen = 12 g, area of specimen = 31.67 cm2 and G, = 2.49. Plot the e, log o' curve. b. Determine the preconsolidation pressure. a.