Determine the anchorage set loss

Q: The beam is loaded as shown below. Given the following properties bw = 305 mm PDL = 120 KN d = 590…

A: Answer  (A) Calculation of shear strength provided by the concrete We know that simplified equation…

Q: Q-2: A simply supported beam is 25 x 50 cm deep and has 2-20 mm Fe 415 grade steel bars going into…

A:

Q: Determine the friction and wobble loss of a post-tensioned prestressed concrete (simply supported…

A: The length of the beam (L) = 15 m The height of the beam (H) = 900 mm The width of the beam (B) =…

Q: (Note: @ does not include beam weight) @D = 2 kip/ft @= 4 kip/ft 12 ft P₁ = 10 kips (A) f = 5,000…

A: Longitudinal section of the beam:Cross-section of beam

Q: y supported beam is reinforced with 5-25 mm diameters at the bottom and 2-20 mm diameters at the top…

A:

Q: A rectangular beam has a width of 300mm and an effective depth of 537.50 mm to the centroid of…

A: Strength reduction factor Strength reduction factors as the name suggests are the factors that are…

Q: The following geomotry and basic clata for a concrete The dam s are given In reservoir figure below.…

A: Consider unit length of the dam.

Q: The floor shown below has a constant thickness (h) of 190 mm, and is supported by beams at each grid…

A: It is required to determine the ultimate load on the slab. wu=1.2DL+1.6LL Here DL is the dead load,…

Q: Compute for the concrete stress in Mpa at the top fiber of the given transformed beam section. M =…

A: Concrete is poured into different materials like molds and tendons and then here they are allowed to…

Q: Given are the following: fc = 55 MPa f pu = 1350 MPa Aps = 1500 mm2 føy = 1100 MPa %3D Use bonded…

A:

Q: A simply supported beam has a section given in (a), with normal-weight concrete compressive strength…

A: Given bw=12''d=24''fc1=4.5 ksifyt=40 ksi Consider the free body diagram; Calculate factored load…

Q: Determine the elastic shortening loss of a pretensioned prestressed concrete

A: Give data: L = 15m H = 700 mm B = 300 mm fpi = 1300 MPa f'ci = 40 MPa Eps = 200GPa total area = 140…

Q: A cross section of a prestressed bonded beam is reinforced by prestressing tendons having a total…

A: The given data is: The beam has a width of 300mm and a total depth of 600mm. Area of prestressing…

Q: Design Beam AB: The beam carries the distributed loads and the concentrated loads as shown: Select…

A: Answer  (1) Selection of section In order to select a section we need to equate Maximum Moment on…

Q: H.W.12: Calculate the design bending strength for the doubly reinforced rectangular section shown…

A: Given data, Compressive strength of concrete= fc' = 30 MPa = 30 N/mm2 Yield strength of steel = fy =…

Q: Calculate yield moment for the beam. Assume concrete accepts no tension. Use fc' = 4000 psi and =…

A:

Q: Determine the shear strength of a 1⁄2-in. 3 2 1⁄2-in. stud, where there are two studs per rib. The…

A: Lower Limit Asα = π0.54 = 0.1963 in2 Qn=0.5Asafc'Ec ≤ RgRpAsaFu =0.50.196343492 = 11.60 kips

Q: The rectangular RC members under uniform load, the cross section of the beam is b×h = 250×500 mm. A…

A: Solution Given Data Md= 100 kNmV=90 kNfc=14.3 MPafy=360 MPa

Q: a simply supported beam is reinforced with 4-diameter28mm at the bottom and 2-diameter 20mm at the…

A:

Q: 14" #3 stirrup 25" 4- #11

A: Solution Given Data f'c=3500 psify=60000 psid=22 in

Q: Problem No. 3 A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume cc=50Omm,…

A:

Q: en below are the pertinent data of a reinforced concrete beam. Beam Width, bw = 300 mm Tension…

A: Given:- bw = 300 mm Tension Reinforcements = 8 – 25 mm dia. d = 512mm  dt = 537mm  f’c = 42 Mpa  fy…

Q: Find maximum factored uniformly distributed load "Wu" that can be supported?, where fe'=30 Mpa and…

A: Answer  f'c = 30 Mpa fy = 400 Mpa As = 3-ϕ16 d = 0.536 m = 536 mm L = 6 m  Calculations shown in…

Q: th of the beam section to the nearest whole number = ___________ kN·m Maximum service uniform live…

A:

Q: 11.) A simply supported 11-m span beam, 300-mm wide by 530-mm deep, is pre-stressed by straight…

A:

Q: Given: Wonderboom catchment (A = 150 km2) in Pretoria North shown in Fig. 2. The slope of the…

A:

Q: constructed sand normal weight concrete that has a compressive strength, fc= 4000psi. Also assume…

A:

Q: H. beam with dimension of (300x 600) mm f = 21 MPa and f = 420 MPa ( C 4m PĮ + 4m with including…

A: Answer  We are given Load P = 25 KN  beam width b = 300 mm beam depth h = 600 mm effective depth d =…

Q: 21. The column of reinforced concrete is loaded with P = 8000 lbs. The modulus of elasticity (E) is…

A:

Q: Design the slab reinforcement if the maximum positive moment is Mup=wul2/11 . and the maximum…

A: Given: length = 6m span = 2m Wu= 8.572 kPa Slab thickness = 150 mm f'c = 28 MPa fy= 219 MPa main bar…

Q: Steel: A= 500 mm? ,- 120 MPa Timber: 1.8 Find the maximum allowable value of P for the column. The…

A:

Q: Compute the forces in the concrete and steel. The compression force in the concrete is C. = 0.85 x 5…

A: Force in the reinforced beam is divided into concrete and reinforcement. Reinforcement can be in the…

Q: 21 in. 24 in. f'c = 6.5 ksi fy = 50 ksi Ec = 3,600 ksi n = 8.0 Mer = 1029 k-in. 3 #8 -16 in- 3 in.…

A: To Find :- stress in concrete and stress in steel

Q: A continuous beam 250 mm x 450 mm carries 6 numbers of 12 mm diameter longitudinal bars as shown.…

A:

Q: Jy Unit weight of concrete = 150 lb/cu.ft. Find the required Shear reinforcement needed at the most…

A: Longitudinal section of beam:Cross-section of beam:

Q: A rectangular beam has a width of 260 mm and an overall depth of 470 mm. concrete cover is 60 mm…

A: We have to find shear and flexure of beam and axial compression force of beam is 80 KN.

Q: 1. The column section shown is reinforced with 10 bars having b-400mm, bar size-28mm, f'c-35MPa,…

A: b = 400 mmh = 600 mmcover, d' = 50 mmMain rebar = 10-28 mmStirrups = 10 mmfc = 35 MPafy = 420 MPa

Q: A reinforced concrete beam used in a processing plant for fruits and vegetables has a beam width of…

A: Given data:- fc' = 24 MPa fy = 240 MPa b = 250 mm d = 400 mm As = 3-16 mm bars To Find :- 1. Stress…

Q: Design the reinforcement of the cantilevered slab (CS – 1) in Figure 3. The slab is to be used for…

A: Given :

Q: Problem No. 3 A beam 200x450mm is reinforced by 2-32mm diameter rebar. Assume Cc- 50mm, stirrups…

A:

Q: What is the concrete stress in the extreme compression fiber (in ksi) if you found the following…

A: Given: Strain, εcen=-0.235×10-3 φ=3.083×10-6 Neutral axis depth from top, yt = 11.2" Modulus of…

Q: Using the following details, Design the shear reinforcement along the length of the beam if it is…

A: Shear reinforcement is used to withstand shear forces that are greater than the concrete's shear…

Q: Q2) Calculate and detail the flexural reinforcement for the beam section shown in Fig.2 at the…

A:

Q: Design Problem 4 The pretensioned rectangular beam shown in Figure 4.0 has straight cables with…

A:

Q: Determine the friction and wobble loss of a post-tensioned prestressed concrete, in percentage form…

A: The length of the beam (L) = 15 m The height of the beam (H) = 900 mm The width of the beam (B) =…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.