A continuous beam 250 mm x 450 mm carries 6 numbers of 12 mm diameter longitudinal bars as shown. The factored shear force at the point of inflection is 200 kN. Check if the beam is safe in bond. Assume M15 mix with = 15 N/mm2 and mild steel with o %3D 250 N/mm2. A clear cover of 25 mm canbe assumed. The design bond stress for mild steel bars in M15 concrete is specified to be 1.0 N/mm2. Section of point of inflection 6 no's of 12 mm dia

A continuous beam 250 mm x 450 mm carries 6 numbers of 12 mm diameter longitudinal bars as shown. The factored shear force at the point of inflection is 200 kN. Check if the beam is safe in bond. Assume M15 mix with = 15 N/mm2 and mild steel with o %3D 250 N/mm2. A clear cover of 25 mm canbe assumed. The design bond stress for mild steel bars in M15 concrete is specified to be 1.0 N/mm2. Section of point of inflection 6 no's of 12 mm dia

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam, which is rectangular, has a base of 250 mm, and d = 625 mm. The beam is singly reinforced, where the recorded strain in the steel is 0.005, and the strain in the concrete is 0.003. fc' = 20.7 MPa, fy = 414.6 MPa. Note: As is not Given a) Determine the value of "a". %3D
The flexural tensile strength of M25 grade of concrete, in N/mm², as per IS:456-2000 is A 0.5 B 5 C 2.25 D 3.5
e. Before loading, the concrete shrinks &z-conc = 0.05 (0.5%). This is less than if it were not restrained by “temperature steel", so the downdrag preloads the steel ơ2-0 = 3,000 psi. When the P = 200K is applied, estimate the final stress in the steel. %3D %3D
Assuming concrete is un-cracked. Determine the cracking moment of the section. E = 2*10°MPa E = 2*10*MPa f' = 20MPA 300 mm 500 mm 3#20 60 mm1
A pre stressed concrete beam has a width of 200 mm and an overall depth of 400 mm. The permissible stresses in tension and compression due to pre- stressing alone are 4 N/mm and 25 N/mm respectively. Find the required pre- stressing force in the tendon and the eccentricity of the tendon, if a straight tendon with a constant eccentricity is to be provided in the beam. No external load or self weight effect is to be considered.
pre stressed conc. solution pls answer
A doubly reinforced concrete beam of size 250 mm x 500 mm overall depth is reinforced with 2-12 mm dia. bars in compression zone and 3-20 mm dia. bars in tension zone, each at an effective cover of 40 mm. The grade of concrete and steel are M20 and Fe415 respectively. The strain in compression steel will be [Take stress in compression steel as 345 MPa]
The T-beam has the following properties: flange thickness = 110 mm flange width = 700 mm web width = 400 mm web height = 250 mm f'c = 28 Mpa a) Calculate the stresses in concrete at uncracked stage under 100 kN-m. b) Calculate the cracking moment. c) Determine the balanced steel area and balanced ultimate moment. The steel is placed 80 mm from its cg up to extreme fiber with yield strength of 414 MPa. NOTE: Please answer the question correctly, if you are not sure about the answer(s) please skip the question. Please box the final answer(s) Thank you
: Calculate the bending stresses in concrete and steel if f, =345 MPa and the concrete strength fe = 30 MPa, n-8. -350mm- 35 kN/m 50 28 750 mm 686 mm -3 m-
Please just do problem 8.2
The modulus of elasticity of "reinforced concrete" in RC design, is O A. 420 GPa B. 200 GPa C. None () D. 220 GPa
reinforced concrete design