Determine radiation heat loss from a steel tube of outside diameter 60 mm and 5m long at a temperature of 327 °C if the tube is inside a square conduit made of brick having 0.4 m side as shown in given figure and temperature of 25 °C. (Take, ɛ(steel)= 0.8, e (brick)= 0.9. Steel tube(1) Brick(2) A 5889.25W B 5656.47W

Determine radiation heat loss from a steel tube of outside diameter 60 mm and 5m long at a temperature of 327 °C if the tube is inside a square conduit made of brick having 0.4 m side as shown in given figure and temperature of 25 °C. (Take, ɛ(steel)= 0.8, e (brick)= 0.9. Steel tube(1) Brick(2) A 5889.25W B 5656.47W

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.48P

See similar textbooks

Similar questions

I want to know how much heat the tube lost due to the material it is made of aluminum or steel. Even if it is a small difference in temperature. I want to know which material Conduct Heat the Best through this problem. material: Aluminum, steel ( the dimensions are the same for both) temperature touching cylinder: 65 Celcius temeprature inside cylinder 64.5 celsius room temperature 24 celcius Tube measurements outer radius r1 r1 = 4 in inner radius r2 r2 = 3 in outer circumference C1 C1 = 25.132741228718 in inner circumference C2 C2 = 18.849555921539 in height h = 8 in wall thickness t = 1 in
Based on the picture above, make a schematic and determine the average temperature difference over the entire length of the tube (ATLM). (value 25)
Sipho’s mother is making a fire in the stove inside a shack using coal. A fan is used to extract the flue gasfrom the fire via a chimney made of zinc material. The wall thickness of Chimney is L=4mm and the walltemperature of the chimney on the flue gas side is T_si=60˚C. Sipho, playing outside next to the chimneyexperiences an ambient temperature of 20˚C. The surrounding temperature is T_sur=35˚C and the emissivityis ε=0.95. Assume the convection coefficient is 20W/m2K and the chimney is grey material.Under these conditions determine the outer surface (air side) temperature T_so=? of the chimney.
solve Temperature at mid-point of the fins.
Hand written plz asap... I'll give you multiple upvote hand written plz asap...
In 2012, a new fiber-optic cable of handling 40,000 telephone calls simultaneously was laid under the Pacific Ocean from California to Japan, a distance of 13,300 km. The cable was unreeled from shipboard at a mean temperature of 22oC and dropped to the Ocean floor having a mean temperature of 5oC. The coefficient of linear expansion of the cable is 75×10-6 /degree celsius. Determine the length of cable that must be carried on the ship to span the 13,300 Km. Also, find the percent change in length
Q3/ For a flat plate collector having the following characteristics as shown in the table; calculate (a) Fin efficiency, (b) Collector efficiency factor, (c) Useful energy, (d) Overall efficiency. Overall loss coefficient 6.9 W/m2 C° Heat transfer 32 W/m C° coefficient inside the tubes Tube spacing Tube outside diameter 120 mm Collector area 4 m 15 mm Flow rate 0.06 kg/s Tube inside diameter 13.5mm τα 0.8 Plate thickness 0.4 mm Global solar radiation 2,88 MJ/m2 for lh Alloy of aluminum, 130 W/m C° Temperature difference 5 C° operating Plate material, k at 20C°
I want to know how much heat the tube lost due to the material it is made of. Even if it is a small difference in temperature. It is a heat transfer problem material: Aluminum temperature touching cylinder: 65 Celcius temeprature inside cylinder 64.5 celsius room temperature 24 celcius Tube measurements outer radius r1 r1 = 4 in inner radius r2 r2 = 3 in outer circumference C1 C1 = 25.132741228718 in inner circumference C2 C2 = 18.849555921539 in height h = 8 in wall thickness t = 1 in
i need the answer quickly
You are designing a 3m x 3m floor with radiant heating. The floor has 12 parallel pex pipes (k = 40 W/mK) of L = 3m, OD = 25mm and ID = 20mm. Hot water (TInfintiy 1 = 90oC, h = 200 W/m2K) runs through the pipes continuously. The surface below the pipes is perfectly insulated. Above the pipes, there is a 3mm layer of bonding material (? = 12 W/mK) and a 9mm layer of tile (k = 2 W/mK). Above the tile, there is air (TInfinity 2 = 25oC, h = 20 W/m2K). Properties of Air: k = 0.025 W/mK, Pr = 0.72, v = 1.847 x 10−5, u = 16.84 x 10−6, p = 1.2 kg/m3, B = 1/Tf (ideal gas), Hint: Assume that the “layer” of pipe starts at the center point (e.g. for conduction purposes, the pipe is OD divided by 2 thick). For convection, consider the entire pipe surface. a) What is the total heat rate entering the room above the floor? b) What is the temperature of the top of the tile?
Q4: A spherical tank, Im in diameter, is maintained at a temperature of 120 °C and exposed to a convection environment. With h. =25 W/m2 C and T 15 °C, what thickness of urethane foam should be added to ensure that the outer temperature of the insulation does not exceed 40 °C . What percentage reduction in heat loss results from installing this insulation. Ans : t = 0.023 m q( W/ ins) = 1982
Fast plz hand written.... I'll upvote if hand written plz asap