Answered: Design the joint and cotter joint to…

Design the joint and cotter joint to resist the load of 100 and 150 kN respectively. The material for both joint is 40C8 FS =3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Pravinbhai
Question (2) Three M30X3.5 ISO grade 8.8 bolts are used in a joint. The joint is being subjected to a maximum load of 210 kN. The joint constant C = 0.35. The bolt has A = 561 mm2, Sp = 600 MPa, Sy 660 MPa, and Sut 830 MPa. The joint members are made of steel having stiffness parameters A = 0.78715 and B=0.62873. The bolts are tightened to 75% of the proof load. Fill your answers in spaces provided: %3D %3D %3D a) Bolt initial load, Fi =D kN b) Bolt tightening torque, T= N.m c) Members' stiffness, Km= MN/m d) Bolt stiffness, Kb- MN/m %3D e) Bolt resultant load, Fs= kN
Using the method of joints, calculate the axial force in each of the bars 1,2,3, & 4 and state whether in tension or compression. 45° 50° 60 30° 45% A B D E F 2P P RA Rs
A column consists of a 2.5 m long hollow tube with an outside diameter equal to 1.5 times that of the inside diameter. The column must carry an axial load of 40 KN without buckling. Use a factor of safety of 5 and calculate the dimensions of the tube if one end is fixed and the other end is free. Use the Euler formula and take ?=200 ???.
The relation between joint and frame is J = (2N - 3) (Where N - number of members, J - Number of Joints ) Sentence is : Select one: True False
From the given illustration below, calculate the reaction of members CD, CE and AE using method of joints.
Problem 2 Assume that Member AB may be considered as long and slender and consider only Euler buckling. What is the critical Euler buckling load and will Member AB buckle? What is the factor of safety of the compressive load with respect to the critical buckling load? Assume buckling only occurs in the plane of the paper. Note: E-30e6psi, I-6.36e-3 in', A-2.83 in², LAB-41.6 in, FAB-540 lb (compression). Also Member OB is 36 inches (3 ft) long. F=270 lbf 3 ft 3 60 A = 45270 LB, n = 83.8, buckles 48400 LB, n = A. Per B. Per C. Per = 1088 LB, n 897, does not buckle 2.02, does not buckle D. Per = 544 LB, n = 0.993, buckles E. None of These
• Bars (1) have a cross-sectional area of A₁ = 0.65 in.2 and a length, L₁= 7 ft. • Bars (1) are made of cast iron with an elastic modulus of E₁ = 24,000 ksi, a coefficient of thermal expansion, a₁ = 12.3 x 10-6/°F and yield strength of oy = 120 ksi. • Bar (2) has a cross-sectional area of A₂ = 1.45 in.² and a length, L₂ = 5.5 ft. • Bar (2) is made of stainless steel with a coefficient of thermal expansion, a₂ = 10.6 × 10-6/°F. • The stress-strain diagram provided below presents the results of the stainless steel's (i.e., Bar (2)) bar tension test. • There is a gap of A = 0.1 in. in the connection at B and a = 3 ft. • All bars are unstressed before a load P = 12 kips is applied and the temperature increases by AT = 40°F. Stress-strain diagram for stainless steel bar: (1) a Stress (ksi) L2 Rigid bar 120 100 80 60 40 20 0 0 0 B (2) P a (1) C Upper scale L₁ Connection details at node C Lower scale. C 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.006 0.008 0.010 0.012 0.014 0.002 0.004 Strain…
A long, slender structural aluminum [E = 69 GPa] flanged shape is used as a l = 9.2-m-long column. The column is supported in the x direction at base A and pinned at ends A and C against translation in the y and z directions. Lateral support is provided to the column so that deflection in the x-z plane is restrained at mid-height B; however, the column is free to deflect in the x-y plane at B. Assume that b; = 102 mm, d = 122 mm, t; = 8 mm, and tw = 6 mm. Determine the maximum compressive load P the column can support if a factor of safety of 2.9 is required. In your analysis, consider the possibility that buckling could occur about either the strong axis (i.e., the z axis) or the weak axis (i.e., the y axis) of the aluminum column. bf C L Lateral B bracing L 2 A
Handwritten recommended.