Design of the Toggle Jack. Lifting load – W, kN is 8 Distance between nuts– B, mm is 50 - 280 Types of threads is Square Length of the links, mm is 140

Q: 7////////

A: The number of degree of freedom or mobility of planar mechanism is given by the following relation…

Q: Make a two DOF linkage with the amount of seven links. Use links that are quaternary and make sure…

A: Make a two DOF linkage with the amount of seven links.Use links that are quaternary and make sure…

Q: Please provide all writeen work and FBD. Thank you

A:

Q: 8-5 lem 8-5 The machine shown in the figure can be used for a tension test but not for a compression…

A:

Q: RB&W¹1 recommends turn-of-nut from snug fit to preload as follows: 1/3 turn for bolt grips of 1-4…

A: Please check the answer in the explanation.     I hope you'll find this helpful.…

Q: The answers I got for A and B are correct. The following is the remaining answers I got which are…

A: Step 1:Based on the information provided in the image, the resultant bending moment acting on the…

Q: Figure below shows a shaft that is loaded as given, l at points B and D to allow the shaft to…

A: In the given problem, Reactions will be determined by treating the beam to be in equilibrium and…

Q: (d) Calculate the mobility using the Kutzbach revision of Gruebler equation. Note: You can watch an…

A: The below figure shows the list of links, joints and higher pairs in the given linkage.The numbers…

Q: 0. Given the following mechanism: how many degrees of freedom (DOF)?

A:

Q: I need the answers to this question.

A: The explanation of the above terms have been explained below.

Q: Draw the assembly views of the following G Clamp from a front view and top view. Provide a standard…

A: To Draw the assembly views of the following G Clamp from a front view and top view.

Q: For a bolted assembly with eight bolts, the stiffness of each bolt is K,=1.0 MN/mm and the stiffness…

A:

Q: What is the length of a belt that is used for a 4” pulley and a 10” pulley that have a center to…

A:

Q: Explain Self-locking and over-hauling conditions for a power screw using sketch and its formula.…

A: Torque Requirement - lowering the load…

Q: For the four-bar linkages below, indicate whether they are Grashof type 1 or 2 and whether they are…

A:

Q: solve the solution with answers given

A: Final Answer:-a) Fc  = 7200lb (part a)b)Fc = 2800lb(part b)c)78.4 ft.IbExplanation:Step 1: Step 2:…

Q: How many primary joints are there in this mechanism? 22.9 22.9 /D E 4.5 typ.

A: Primary Joints include pins, sliders and other elements that allow pure rotation or pure linear…

Q: Required information A power screw is 22 mm in diameter and has a thread pitch of 5 mm. Find the…

A: Thread width is 2.5 mmExplanation:Thread Depth : h = P/2​Thread Width : b = P/2​Mean Diameter : Dm…

Q: A screw jack mechanism is shown in the figure below (not drawn to scale). A belt drives a sheave…

A:

Q: solve/ show solution for given answer equations  kb = (Ab*Eb)/ g and kc = (Ac*Ec) / g   G is the…

A: I have attached the image below .Explanation:

Q: Consider a thread callout of Dia 0.500-24 UNF-3A. Based on the information given, how far will the…

A: Given    0.500-24 UNF-3A From the Unified Screw Threads, Standard Series     Pitch = 0.4675 in