Design a voltage regulator circuit to supply a constant voltage of (10 V) across a resistive load of (10 2). The minimum Zener current is (50 mA) and maximum current is (800 mA). Assume Rs = 10 Q and Find: - 1- the maximum and minimum source voltage. 2- at the maximum source voltage, find the minimum load resistance. 3- at the minimum source voltage, find the maximum load resistance. 4- minimum and maximum power dissipated in the Zener diode.

Design a voltage regulator circuit to supply a constant voltage of (10 V) across a resistive load of (10 2). The minimum Zener current is (50 mA) and maximum current is (800 mA). Assume Rs = 10 Q and Find: - 1- the maximum and minimum source voltage. 2- at the maximum source voltage, find the minimum load resistance. 3- at the minimum source voltage, find the maximum load resistance. 4- minimum and maximum power dissipated in the Zener diode.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q5/ A/ If a Class B push-pull each Tr. Has V CEQ = 50V Calculate Ic sat. ( rc = 500 0, re = 0) %3D %3D B/ For the Zener diode circuit if Pz max = 27W and Vz = 10V find IZmax. C/ For the C.E voltage divider bias circuit shown below. 1- Draw the AC analysis for the cct. 2- Write the equations for Zi, Zo, Av, Ai |+ VCC R1 RC C2 C1 Ac o/p B Ac i/p Zo R2 RE СЕ Zi
Draw the wave shape of the output voltage (VOUT) of the following circuit. Assume both theSilicon zener diode breakdown voltage to be 10V & peak input voltage VP to be 20V.
2. Plot the transfer function, and clearly indicate the on/off conditions of each diode, the slope of the line, and the voltages of turning points in each operating region for the following circuits. Assuming the constant-voltage model (VD,on = 0.8 V) is used to determine the DC level. Also, Plot the output waveform in time-domain if the input signal is as shown below with the amplitude and other important values labeled in the figure. (a) (b) Vin R= 500 D₁ V₁= 2.5 V D₂ A V₂ 1.6 V D₁ 2R 2X4 2R D₂ 3R out Vout Vin Vin 10 mv 1-AAAA-3.4 V >t 5 V
INCLUDE ALL THE DECIMALS
A single phase, fully controlled bridge rectifier supplies a series connected resistor- inductor load (R = 20, L = 0.02H) from 220V, 50HZ AC supply. The triggering angle of the thyristors is 60°. (Assume the circuit is ideal.) a. Sketch the circuit. b. Develop the load current expression and check the continuity of the load current. c. Sketch the load voltage and load current waveforms. d. Calculate the mean values of the load voltage and load current. e. Sketch the inductor voltage and calculate its mean value. f. Calculate the FF (form factor) and RF (ripple factor) of the load voltage.
1. Briefly describe what a Schottky junction is and how it is formed. Draw the energy band diagrams of a Schottky junction under equilibrium, forward bias, and reverse bias.
2 V 1ΚΩ VOUT Find the following: a. Vout b. Small signal model of the diode under these conditions (Do NOT consider capacitance across the diode junction and the resistance of the semiconductor material outside the diode junction) c. Approx. peak-to-peak value of the AC component of Vout if a 1 mV RMS sinusoidal signal is added to the 2 V DC source. Given that: reverse saturation current is 1.5 x 10-14 A, ideality factor is 1.1, and the circuit is operating at 27°C.
Design a 15 V Zener regulator for the following conditions: 1) The load current IL ranges from 200 mA to 300 mA.2) The source voltage ranges from 21 V to 25 V. Based on your design results,a) Draw the Zener regulator circuit.b) Calculate the power ratings for both Zener diode and resistor Ri
An intrinsic semiconductor is neither a good conductor nor a good insulator. Select one: O True O False A varactor is a pn junction diode that always operates in reverse-bias and is doped to maximize the inherent capacitance of the depletion region. Select one: O True O False A simple diode rectifier has 'ripples' in the output wave which makes it unsuitable as a DC source. To overcor this on e can use
Design a POWER SUPPLY with 5V output voltage. Use zener diode as a voltage regulator. Then solve for theoretical computations. Thanks!
a2/a-Design Circint as the following peseripton: A. the positive cycle of the vout signal is 3.2 and Neyatine cycle is 4.3 (Note: we must used preetical Diodes aned vin is tov) B- the pesitive cycles of vout is s-3 od Negative cycle is (5 4) [te:Comsider vin = 1ovavd we must used Capaetor with praeticul Didde)
Show the downward shift of the output signal with the series capacitor and diode.Clampers or DC restorers are clamp a peak of a waveform to a specific DC level comparedwith a capacitively coupled signal which swings about its average DC level (usually 0V).If the diode is removed from the clamper, it defaults to a simple coupling capacitor– noWhat is the clamp voltage? And, which peak gets clamped? Why is this so? Voltage values: Capasitor value: 1000 pFDC offset: 0 VAmplitude: 5 VFreq: 1 KHz