Design a simply supported rectangular reinforced concrete beam. Note: The self-weight of the beam is not included. 6OKN 6kN/m 650mm Wa (LL) h 2 m 7.25m b 350mm bar dia =20 No. Of layers =two Fc mpa=25 Fy mpa =350

Design a simply supported rectangular reinforced concrete beam. Note: The self-weight of the beam is not included. 6OKN 6kN/m 650mm Wa (LL) h 2 m 7.25m b 350mm bar dia =20 No. Of layers =two Fc mpa=25 Fy mpa =350

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The load is supported by the four 304 stainless steel wires that are connected to the members AB and…

A: We have given the following data :

Q: Hand

Q: How much service live load, in kN/m, can be supported? The member weight is the only dead load. The…

Q: For the reinforced concrete beam shown, determine the area of the steel r inforcement for a balanced…

A: Introduction- The Reinforced concrete sometimes known as reinforced cement concrete is a composite…

Q: SP 1 The diameter in fig are 90 cm and 60 cm, at the larger end the pressure is 9.81 kpa, neglecting…

Q: 10/10 find the tensile stress in upper plate in section 1-1 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80…

A: Width of plate (B) =300mm Diameter of bolt(d) =10mm Thickness of bolt (t) =8mm Number of bolt at…

Q: 1-6. Consider the loads of Fig. P1-6 to be axially applied at sections A, B, C, and D to the steel…

A: Given: Cross sectional area of steel bar = 3 sq. in Solution: (Please refer images below for…

Q: 2.5 The steel propeller shaft ABCD carries the axial loads shown in Fig. (a). Determine the change…

Q: How much service live load, in kN/m, can be supported? The member weight is the only dead load. The…

A: Service dead load = 45 kNService live load = 90 kNGross area, Ag = 18400 mm2Radius of gyration, ry =…

Q: calculation and draw SFD and BMD.

A: Determine the support reaction and draw the shear force and bending moment diagram of the given…

Q: 500 mm 62.5 mm 375 mm 62.5 mm Determine the total required number of 20mm bars to be used in two end…

A: Given data, Pu = 800 kN Mu = 120 kNm fc = 20.7 MPa fy = 413.7 MPa Size of column = 300×500 mm Clear…

Q: 4.8 Member AB is the beam under consideration. As shown in the illustration of the loading…

A: in the question, the free body diagram is provided also the load of 500-lb/ft uniformly distributed…

Q: HW Draw S.t,B.M and elasticaiagams for the beam Shown beloi by using method of equations? low 4 KW…

A: Introduction : The sum of all transverse forces applied on either side of a portion of a beam…

Q: Determine the force of member BD. Include a negative sign if the answer is in compression. Indicate…

Q: by 늘 wo B 늘 C X

A: Given Data:Length L=6.3md=300mmbf=215mmtf=14mmtw=10mmIt is required calculate the largest intensity…

Q: 3.4 Check the threshold validity below according to the bending requirement if 35MPa=m, f = 300 MPa.…

A: Dead load, DL = 5 kN/mLive Load, LL = 10 kN/mPL = 20 kNSpan, L = 4 mfc = 35 MPafy = 300 MPa3-25 mm…

Q: The cross-sectison of a simply supported plate girder is shown in figure. The loading on the grider…

Q: 1. Draw the bending moment diagram ? 2. Find the value of the maximum bendig 3. Find the value of…

A: UDl of 4kN/m for 2m lies at the center of the beam Total load on the beam = 4x2 =8KN Apply…

Q: A flanged cros5 section is Used to suppaut the lcads shown on the beam on the et page. The dimen…

A: Determine the cross-sectional area and moment of inertia. The cross-sectional area of the beam is A.…

Q: A pipe column is braced to prevent bending and buckling. It is subjected to a compressive load of…

Q: (1) SOL (2) SLL Calculate the Long-term deflection assuming that 25% of the live load is…

Q: *R12-8. The member consists of two triangular plastic strips bonded together akong AB. If the glue…

A: Given Data: The allowable shear stress of the glue is τallow=4.2 MPa. The height of each triangular…

Q: VINY A Sted wire of 8mm diametel is used for lifting ** at it's lower end the the aa lood of 1200…

A: Diameter of steel wire = 8mmP= 1200NL= 150000mmModulus of elasticity = E = 2×10⁵N/mm²Unit weight of…

Q: midpoint of the structure. The 275mm x 330mm (WxH) beam has the following properties: f’c = 29 MPa…

Q: Select an A992 W shape for beam AB of the floor system shown in Figure. In addition to the weight…

A: Consider the given floor slab. The dead load on the beam comprises the slab weight and beam weight.…

Q: Determine the values of S and Z and shape factor about horizontal x-axis. 14-in 2.5-in 2.5-in 1/2…

A: y = A1y + Ay2 +Ay3 A1 + A2 + A3⇒y = .5×6×3 + 16×.5×6.25 + .5×6×3.5×6 + 16×.5 + .5×6⇒y = 4.8571 in…

Q: The T-beam used in a heavy storage warehouse is made of concrete having a specific weight of 19.6…

Q: H / The beam shown below has across seclion of channel Shape with widhth 360mm and haghs h= loomm,…

A: Web thickness = 14mm Width of the beam = 360mm Height of the section = 100mm Unifrom loading =…

Q: 10.8m 8.1m D ALANISH 100KN 130kN 150KN 160kN 140KN H 120kN 8 panels @ 6m ea. = 48m Determine the…

Q: An insulated T-beam has a flank 2400 mm wide and 120 mm deep. The width and Effective depth of the…

A: Step 1:The moment of resistance (Mr) = Total compression x lever arm The moment of…

Q: Assuming the section is uncracked, Compute the cracking moment in KN.m.

Q: A bronze pipe (1) is to be connected to an aluminum alloy pipe (2) at flange B. When put in place,…

Q: 0:Design the steel reimforcement for flexural for the beam shown m the kN fig.below The dead load on…

A: if the size of beam is known and area of reinforcement is need to design then their is 2 cases 1-…

Q: A simply supported beam spans 8 m. It carries the uniformly distributed load throughout of its…

A: Steel beam.. W section Calculate of flexure strength at plastic condition

Q: Compute the loads and deflections point D at each yield and the ultimate level for the structure…

A: The forces are the amount of loading that happened on the area required by the specimen. The…

Q: 100kn 2okn 50kw 25tW 15k A 30 3m しし 20kN 2okN 20k 3m 3m Sulve for indicete units & if in comp. FAB,…

Q: Design a simply supported rectangular reinforced concrete beam. Note: The self-weight of the beam is…

A: Given, Wu D.L. = 90 kN/m Wu L.L. = 70 kN/m fy = 350 MPa fc = 21 MPa diameter of bar = 20 mm Number…

Q: Determine the force in member BE of the loaded truss. The force is positive if in tension, negative…

Q: 0.8 m 643m 15 AN C LOM D VN 120

A: Given Data:UDL=6kN/mConcentrated Load = 15kNSpan =3m

Q: W36 X 160. Include self-weight. Solve for Fb, Fv, and max. deflection. Also added a sheet I have…

Q: PROBLEM 2: The steel beam loaded below has the built-up cross section as shown. Determine the…

A: Calculate the support reactions of the given beam: RA=RB=wL2=5w

Q: Question 2 1 0.4m 1 0,5m A ↑P d=20mm - de вони munt Both partion of rod ABC are made of on a Ruminum…

Q: + 13ksi 7ksi 10ksi 10ksi 7ksi 13ksi

Concept explainers

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur, chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.

Question

Design a simply supported rectangular reinforced concrete beam.
Note: The self-weight of the beam is not included.
6OKN
6kN/m
Wa (LL)
650mm
2 m
7.25m
b
350mm
L
bar dia =20
No. Of layers =two
Fc mpa=25
Fy mpa =350

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Calculation for maximum moment

VIEW

Step 3 Design of singly reinforced beam

VIEW

Step 4 Design of singly reinforced beam

VIEW

Step 5 Number of bars

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Date No. Cheek Deflection for Simply supported Girder Bridga :- Span L-20 DL from Section o.w weight = As 18020 C Ec-2.2x106 +252 feu-250 kg/cm² fy, 3600 kg/cm2 DL LL 1.681 2.7 2.7 11.68 1.5 2.2 2.2 0.5 0.2 2.2 D.S 0.2
Based on the bridge truss show below determine the force acting at members DF, GI, and LM using method of section.
DETERMINE THE THE IS MAXIMUM SAFE SERVICE LIVE LOAD THAT THE BEAM CAN CAN CARRY IF SERVICE DEAD L O A D THE BEAM WEIGHT OF THE BEAM SECTION fy = 415 MPa. TOP BARS BOTTOM BARS ARE CENTER DISTANCE 12 KM/M INCLUDING AND BASED ON THE CAPACITY SHOWN. fc : 40 MPa AND ARE 6-32 mm. AND ARE - 3 - 28 mm. CENTER TO 3 BETWEEN THE USE 2015 NSCP Is 108 mm 00 0 0 300 G ט1 108 352 70. A (1 7.2m B TOP BAR LAYERS ↓ 6.7M C OM
H.W Draw S.f,B.M and elastic dliagrams for the beam Shown below by method of equntions ? 6W/m 20 KN 6m 2m 2m
Detailed Calculation - RCD
kindly please help me answer this question, please be accurate and detailed when it comes to the solution. thank you.
Can u please find the Deflection(d) for the Given Compound-steel beam. Please solve on paper sheet as soon as possible.
Find CD, EF, AF, AB 15 ft E F B CO с 15 kips H OD +12 ft 12 ft-- 12 ft-12 ft-12 ft- I'll edit this later 2 in compression, 2 in tension, 3 are 36 kips, 1 is 45 kips
Determine collapse load Wu for continuous beam ABCDE loaded and supported as shown in figure . For span AC plastic moment of resistance is 50 % more than that of CE .
How Determin # As for the beam show in figre (including self weight) (P=35 M²-i fy=420) well kN/m WL=24 K~/3 590 250 5m
1.)Calculate the height of the neutral axis measured from the extreme compression fiber. 2.) Calculate the strength reduction factor for the given beam. 3.) Calculate the design moment for the given beam. Given b=9.25mm d=152.5mm d(prime)=32.5mm L=1.1m WsubD=6.25kn/m WsubL=8.25kn/m 4 25mm tension steel bars 4 12mm compression steelbars FsubC(prime)=28Mpa FsubY=420Mpa