Answered: Design a rectangular beam reinforced…

Design a rectangular beam reinforced for tension only to carry a uniform load of 22500 N/m exclusive of its own weight. Assume the beam to have a simple span 6m. Use ACI specs, with fc=20MPa,

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter2: Concepts In Structural Steel Design

Section: Chapter Questions

Problem 2.1P: A column in a building is subjected to the following load effects: 9 kips compression from dead load...

See similar textbooks

Related questions

Q: A rectangular beam has width 300 mm and effective depth of 450mm .The beam reinforced with four 028…

Q: Given: T Beam A shown below spans 32 ft (simple span) and supports the floor system shown. Typical…

Q: under the following boundary conditions (x = 0, y = 0); (x = L, y = yMax). what kind of beam is…

A: Beams can also be described with their boundary conditions. In the given question, When x=0…

Q: A plain concrete beam has cross-sectional dimensions of 15 in. by 15 in. The concrete is known…

Q: 14x22 beam is subjected to a moment of 55 ft-kips. What is the bending stress in th pe your…

Q: 1.4 A rectangular beam has width 300 mm and effective depth of 450mm.The beam reinforced with four…

Q: 1. A 100mm x 200mm timber beam has a span of 4.0m and carries a uniform load of 15kN/m. including…

A: Given data, Span of beam, L = 4 m Uniform distributed load acting on the beam, w = 15 kN/m Depth of…

Q: Assume that a max stress is to be the limiting factor in selecting a box-beam having a span length…

A: Span length, Yield strength, Load at free end, Safety factor, To find: Minimum section modulus.

Q: ANALYSIS AND DESIGN OF DOUBLY REINFORCED CONCRETE BEAMS 1. A rectangular beam with a width of 350mm…

A: Solution: Analysis of doubly reinforced beam has the following scenarios 1. Both tension and…

Q: f) the maximum bending moment in the beam. Enter your answer in kNm to 3 decimal places.

A: Given figure is a simply supported beam. Point load = 3.3 kN, acting at the midspan. Total span…

Q: The truss problem for this semester is the problem below. Find the maximum compression and the…

Q: Assume that a max stress is to be the limiting factor in selecting a box-beam having a span length…

Q: Solve for the required compression steel area, A's in mm² at midspan of the rectangular beam in the…

Q: P = L1 = L2= L1 Your Answer: P 195 2.50 4.5 Answer KN m m L2 ▷ View hint for Question 1 P The…

Q: A W530 × 72 is used as a simply supported, uniformly loaded beam with a span length of 15 meters…

A: Given section is W 530 x 72 Length of beam (l) = 15m σy (Yield strength of section) = 414MPa =…

Q: 4. An unequal angle bar 150 mm x 75 mm thickness of metal 8 mm is meters with its longer leg placed…

Q: I cross-section is simply supported on a span of 4m. Find the safe uniformly distributed load the…

A: Draw the schematic diagram

Q: A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 52 kN/m, LAB = 1.7…

Concept explainers

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.

Question

100%

Design a rectangular beam reinforced for tension only to carry a uniform load of 22500 N/m exclusive of its own weight. Assume the beam to have a simple span 6m. Use ACI specs, with fc=20MPa,

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given that;

VIEW

Step 2: Step-1 Calculation of maximum Bending moment;

VIEW

Step 3: Step-2 Let us consider the width of the section=250 mm;

VIEW

Step 4

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
Use the composite beam tables and select a W-shape and stud anchors for the following conditions: Span length = 18 6 Beam spacing = 9 ft Total slab thickness = 51 2 in. (the slab and deck combination weighs 57 psf). Lightweight concrete with a unit weight of 115 pcf is used Construction load = 20 psf Partition load = 20 psf Live load = 225 psf Fy=50 ksi and fc=4 ksi A cross section of the formed steel deck is shown in Figure P9.8-9. The maximum live-load deflection cannot exceed L/360 (use a lower-bound moment of inertia). a. Use LRFD. b. User ASD.
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
The frame shown in Figure P4.7-8 is unbraced, and bending is about the x-axis of the members. All beams areW1835, and all columns areW1054. a. Determine the effective length factor Kx for column AB. Do not consider the stiffness reduction factor. b. Determine the effective length factor Kx for column BC. Do not consider the stiffness reduction factor. c. If Fy=50 ksi, is the stiffness reduction factor applicable to these columns?
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.
Note For Problems 9.6-1 through 9.6-5, use the lower-bound moment of inertia for deflection of the composite section. Compute this as illustrated in Example 9.7. 9.6-4 For the beam of Problem 9.4-1, a. Compute the deflections that occur before and after the concrete has cured. b. If the total deflection after the concrete has cured exceeds L240 select another steel shape using either LRFD or ASD.