Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 400 N to 980 N. The spring index is 6.8 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm.

Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, to sustain a load, which varies from 400 N to 980 N. The spring index is 6.8 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa, find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When a coil spring with a spring rate of 150 lb/in. is compressed 1.5 in., the coils are closed. The allowable shear stress is 60,000 psi, the spring index C = 6, the ends are squared, and G = 12 x 106 psi. Calculate: a. The required wire diameter d, b. The required coil diameter D, %3D C. The required number of coils, d. And the closed length of the spring.
3 In a compound helical spring, the inner spring is arranged within and concentric with outer one but is 10 min shorter. The outer spring has 10 coils of mean dianmeter 30 min and wire dia 3 mm. Find stiffness of inner spring if an axial load of 100N causes outer one to compress by 20 mm. If the radial clearance between the springs is 2 mm, find wire diameter of inner spring which has 8 coild. G 80 kN/mm.
A helical compression spring is required to provide a minimum force of 150 lb at installation and have a working deflection of 1 in. The spring rate is 75 lb/in. The coil must fit in a 2.1-in-dia hole with 0.1 in total clearance. Use 0.25-in diameter unpeened music wire and squared/ground ends. Use a 15% clash allowance, shear modulus G = 11.5 Mpsi, and weight density γ = 0.285 lb/in3. Assume Sys = 0.6Sut. Part A Find the shear stress at the initial deflection. Express your answer in pounds per square inch to three significant figures. τiτi = Part B Find the mean stress. Express your answer in pounds per square inch to three significant figures. Part C Find the alternating stress in the coil. Express your answer in pounds per square inch to three significant figures. Part D Find the fatigue safety factor for infinite life in shear. Express your answer using three significant figures.…
=3-456 Nm (Ans.) Example 14-8. For a close-coiled helical spring subjected to an axial load of 300 N havina 12 coils of wire diameter of 16 mm, and made with coil diameter of 250 mm, find: (i) Axial deflection; (ii) Strain energy stored; OVed
The spring of the check valve seen in the figure is mounted with a pre-stress of 12 mm and the diameter of the Spring Wire is 2.7 mm, the number of winding is 13, the slip module is 80800 N/mm?, the average diameter of the winding circle is 23 mm. If these conditions are taken into account, check the spring strength by finding out how much pressure the check valve will open at. Publication safe shear stress value is 185 N/mm? and 1 bar = 0.1 N / mm? will be taken. Ø10
The material is a spring wire has a shear modulus of 1.2 x 107 lbf/in2. The maximum allowable stress under design conditions is 50,000 lbf/in2. The spring index is 7. Assume the maximum stress is experienced when a 700 lbm object falls from a height of 46 in above the tip of the spring, impacts squarely on the spring, and deflects the spring 10 in. Determie:1. The minimum wire diameter is most nearlyA. 0.58 in B. 0.88 in C. 1.4 in D. 1.8 in2. The mean coil diameter is most nearlyA. 8.6 in B. 10 in C. 13 in D. 16 in3. The number of active coils is most nearlyA. 8 B. 11 C. 12 D. 14
I need the answer as soon as possible
A coupling GY8 is fixed on a shaft by a type C flat key, as shown in the figure. And the dimensions are also shown in the figure. The torque working on the shaft is 900N-m. [op]=100MPa. Please choose the dimension of the key and check its strength. op 27 = ×10³ kld 1. Note: Standard dimension series of flat key Diameter of shaft d >44-50 Width of key bx Height of key h 14x9 Length of key >75-85 >85-95 22x14 25×14 >50-58 >58-65 >65-75 16x10 18x11 20×12 6, 8, ..., 80, 90, 100, 125, 140, 160, 180, 200... Shaft 140 Coupling 70
A helical compression spring is made with oil-tempered wire of diameter 0.2", mean coil diameter of 2", 12 total coils, 5" free length, and squared ends. (a) Find the solid length. (b) Find the force required to compress the spring to closure? (c) Find the factor of safety against yield when compressed to the solid length. (Hint: Uses Say= 0.5 Sut for shear strength.)
An eccentric Cam, too mamindiameter eccentricityof lomm as s'hown in the figure. The roller followeris held ag ainst the Cam by means of a helical - amp- ression spring. The force between the Camand the follower varies from 100N at the lowest position to 350N at the highest position of the followers Design the from static rotates with an SPRING FOLLOWER spring Consideratron and determine the factor of safety for fatigue Gonsiderations. Neglect the effect of inertia frces. Note: assume for this state the - handened and tempered steel-wire sw grde, and e= 6. 100
A helical compression spring shown in figure, experience a minimum force of 150 lb at just before ignition. During the working cycle it experiences addition force as it is compressed by an inch. The spring rate is 50 lb/in. The coil must fit in a 2.1-in-dia hole with 0.1 in clearance. Use 0.25 in diameter, peened, OQ&T wire and squared/ground ends. Find a) The stresses and safety factor for infinite life fatigue. b) Calculate the number of the coils. (Shear modulus G= 11.5 x10^6 psi) Note that for peened springs, Zimmerli's finding is updated as follows: Ssa = 57.5 kpsi (398 MPa) and Ssm = 77.5 kpsi (534 MPa) Expansion Just before Ignition
2. The design of the crank for a shredder is shown below. The applied force P on the handle is 200 N producing a bending moment and torsional load on the shaft. The dimensions x is 200 mm. Assuming that the resulting bending stress is repeated and reversed and the torsional shear stress is constant, specify a material and size for the shaft. Use a stress concentration factor of 2.5 and a design factor of 3. SHAFT R (1/10d} R (1/10 d) 120.00 PSI p9