Design a common-emitter amplifier with an NPN transistor with B = 100 and whose voltage gain is - 20, Zin> 5K, Zout> 5K. The amplifier is biased in a voltage divider configuration with a bias source of + 20V and the peak AC input voltage is 300mV. The amplifier load is 1K. 1. Design of the polarization circuit.

Design a common-emitter amplifier with an NPN transistor with B = 100 and whose voltage gain is - 20, Zin> 5K, Zout> 5K. The amplifier is biased in a voltage divider configuration with a bias source of + 20V and the peak AC input voltage is 300mV. The amplifier load is 1K. 1. Design of the polarization circuit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Ce301 q4a/b
6) Determine the following parameters according to power amplifier BJT circuit which is given below. 6.a) Calculate input power, output power and efficiency of the amplifier circuit. 6.b) Draw the load line using parameters which are found above and show Q point on it? Vcc Rc = %3D RB = C; .. Figure 5. Power Amplifier Circuit
a) Assume that i) both the coupling capacitors and the emitter capacitance are large enough to have zero impedance (i.e. short circuits), ii) the frequency of input signal is low enough to ignore transistor internal capacitances. Consider the common emitter (CE) amplifier shown in Figure Q1.a. 1) Draw the low-frequency small signal equivalent circuit considering the above assumptions. 2) Show that the maximum voltage gain is Ay(max) = –40lcRc if ro « Ta, (R1//R2) » r7, Tq » Rs, R, » Rc. o+V ce R C. R, Rs C. RL R, RE OV Figure Q1.a
6.13 POST LAB QUESTIONS 1. Define current gain in CE configuration? 2. Why CE configuration is preferred for amplification? 3. What is the phase relation between input and output? 4. Draw diagram of CE configuration for PNP transistor? 5. What is the power gain of CE configuration? 6. What are the applications of CE configuration?
Question 2 Referring to Figure 2 and the following BJT parameters: B = 100, thermal voltage = 25 mV and VBE = 0.7 V. a. Calculate the DC operating point of the BJT which are the collector current, Iç and base-emitter voltage, VCE. b. Draw the low-frequency small-signal equivalent circuit for Figure 2. Vcc 10V Re $4.7 ka R 47 ko3 HS vo B=100 Vthermar=25mv R. 10 Κl R $ikn T10UF GND Figure 2
Vsis (~ Q3 (a) What is the advantage of using MOSFET as compared to BJT at the first stage of multi-stage amplifier? Rais 600 02 www Z₁ (b) Describe the function of the capacitor for the following condition: (1) (ii) SEEE/SKEE 1073 (c) The transistors parameters in Figure Q.3 are given as follow: BJT (iv) ↑ B-350, VBE 0.7 V, Ic=0.3 mA, VT 26 mV, and ro=00 E-MOSFETk 0.8 mA/V², VT- Vas(T) = 1 V C₁ HE a capacitor between stage 1 and stage 2 of a RC-coupled amplifier. bypass capacitor which is commonly used in small signal amplifier. (i) Draw the ac equivalent circuit at middle frequency for circuit in Figure Q.3 by using hybrid-x model. (ii) Determine the values of Z., Ziz and Zo. (iii) Calculate the gain, v/v, in decibel (dB). Draw and label the waveforms vo when v=2 sin 50t [mV] for one complete cycle. + Roi 50 ΚΩ Vi Ra 6 kn Ro 4.5 k Q₁ Rs 3 kQ C₂ не +15 V DS ↑ 22 R₁ 75 k R₂ 9 kn Figure Q.3 Multistage amplifier circuit Re RE 2kQ Rez 1kQ ← 2₂ -C₁ R₂ 20k2 %
Elecronics Engineering
2. The parameters of the transistor as shown in the figure below are ß = 100 and VA = 100V. a. Find the dc voltages at the base and emitter terminals. b. Find Rc such that VCEQ = 3.5V. c. Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = Vo/Vs. d. Repeat part (c) if a 5000 source resistor is in series with the vs signal source. V+ = +5 V Rs = 100 £2 www Us Cc RB = 10 ΚΩ I= Iausmi 0.35 mA www RC -000 V=-5 V CE
Common Gate MOSFET Amplifier has Select one: a. input is connected to the Gate and the output is taken from the Source b. input is connected to the Source and the output is taken from the Drain c. input is connected to the Gate and the output is taken from the Drain d. input is connected to the Source and the output is taken from the Gate 55 week 10 material Jump to... CE255/EE255 (01)- 16
c) Figure 2.3 shows the circuit diagram of a typical npn BJT common emitter amplifier. The values of RB1-30 kOhm, RB2=10.XY kOhm, Rc-3.XY kOhm, Ic=2.XY mA and Vcc=24 V. If the transistor current gain 3 = 50 determine using the full analysis and assuming VBE = 0.7 V the value of RE, hence identify the location of the Q-point (Ic, VCE, IB and VBE). Now sketch the AC circuit model of this amplifier and determine the value of the ac open circuit voltage gain Av and the ac short circuit current gain Ai. (Assume that Vth = 26 mV). Vin RB1 Cin lin RB2 -10 Rc VB RE + Vcc Vc Cout VE www li Figure 2.3 Vout Ce ¡out x=1 y=7
Which of the following is the basic feature of the emitter-connected amplifier circuit? I. It has voltage gain II. It has current gain III. There is a 180 degree phase difference between the input signal and the output signal
Please all subpart is compulsory for like this please Asap