3-bit Synchronous Countera. Preliminary WorkDraw state diagram, state table, Karnaugh maps and diagrams of the design. Construct andtest the designed circuits in MaxPlus II.b. Еquipments• JK Flip Flops (74LS73 or 74LS76) and other necessary ICs such as Inverter,OR, AND• Breadboard• Connection cablesс. ЕxperimentDesign a 3-bit synchronous counter using logic gates and JK flip flops. The circuit shouldoutput your number without repetition in MOD 8. For example, for a student number1900510082 the circuit should output 1,0,5,2 in succession. (MOD 8 produces1,1,0,0,5,1,0,0,0,2 and without repetition it counts 1,0,5,2)

Let us take my no. is 1900510082, so without repetition synchronous counter need to count 1,0.5.2.…

Design a 3-bit synchronous counter using logic gates and JK flip flops. The circuit should output your number without repetition in MOD 8. For example, for a student number 1900510082 the circuit should output 1,0,5,2 in succession. (MOD 8 produces 1,1,0,0,5,1,0,0,0,2 and without repetition it counts 1,0,5,2)

Design a 3-bit synchronous counter using logic gates and JK flip flops. The circuit should output your number without repetition in MOD 8. For example, for a student number 1900510082 the circuit should output 1,0,5,2 in succession. (MOD 8 produces 1,1,0,0,5,1,0,0,0,2 and without repetition it counts 1,0,5,2)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

I need the answer as soon as possible
Logic Design
Figure shows a state diagram for a sequential circuit. Design a sequential logic circuit using JK flip-flops with individually controlled JK that implement the state diagram of Figure 3. 0 00 11 1 0 1 0 1 01 10 0
Design a state diagram to detects 0010100 overlapping input sequence (repeating). The output is at logic level "1" when the sequence is detected, Otherwise the output is "0".
create the schematic needed for part b and c please
D. Design a sequential circuit with eight (8) states and the state transitions are defined in the table shown below. (a) Derive the state table with JK flip-flop inputs using the JK flip-flop excitation table. (b) Derive the JK flip-flop input equations. Present State a b C d h Next State x = 0 8 d f 8 x = 1 b C e a C b h a Output x = 0 0 0 0 1 0 1 x = 1 0 0 0 0 0 1 0
create the schematic needed for part d please
Consider the following circuit with 2 inputs (X and Y) and 2 J-K flip flops.· When X=0, the output (Q1Q0) preserves its value regardless of the value of Y.· When X=1 and Y=1, the output (Q1Q0) counts up by one (00-01-10-11-00 …).· When X=1 and Y=0, the output (Q1Q0) counts down by one (00-11-10-01-00 …). a) Derive the state transition, output table.b) Derive flip-flop excitations (logic expressions).c) Draw the circuit implementation using only 2-input NAND gates to drive the inputs J0and K0, and only multiplexers (MUX) to drive the inputs J1 and K1.
Design and explain a four stage frequency divider digital circuit uses J-K flip flops and a 600Hz clock signal that is applied to the clock input of the 1st flip flop
For a sequential logic circuit that detects 010011 sequences in binary information received from an external input line x and makes external z output 1 when detected; a) Create the state diagram. Explain how you created it. b) Create the situation table. Note: D flip-flops are used in this circuit. If there are unused states in the state table, you can specify the next state values and output them as inactive values.