Describe the force exerted by the oil on the gate What does the center of pressure mean? And why is it always located below the centroid of the submerged surfaces? Draw a sketch showing the location of the centroid and the center of pressure 1 m SAE 10W-30 A Gate 2 m B

Q: For the body shown. If point P3 is the center of mass for rod part P1-P2, and point P4 is the center…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: If block B is moving downwards with a speed of 2 m/s at the instant shown, Determine the speed of…

A:

Q: 2) A car travels along a circular road with aradius of curvature of 75 m, and velocity of 10 m/s.…

A: Given Acceleration at 15 m  can be determined as

Q: The blades of a large wind turbine, designed E generate electricity, sweep out an area 1400 m and…

A: Given that, Swept area, A=1400 m2,Speed of air, v=15 m/sec, (a) The mass flow rate through the wind…

Q: The 500MB jet airliner has three engines. each of which produces a nearly constant thrust of 250 kN…

A:

Q: A steel pipe of 100 mm bore, and 10 mm bore thickness, carrying dry saturated steam at 28 bars, is…

A: Given:Pipe inner diameter, d1=100 mm=0.1 mThickness of pipe, t1=10 mm=0.010 mSteam condition inside…

Q: Determine the magnitude of the force (in N) of the y-component of the internal pin at B.

A:

Q: Steel Bronze Area (mm) 600 300 3. Figure (a) shows a rigid bar that is supported by a pin at A and…

A:

Q: a stone is thrown vertically from a 100 ft tower with initial velocity = 50 ft/ sec ,at the %3D same…

A:

Q: A man exerts a force Fon the handle of the stationary wheelbarrow at A. The weight of the…

A:

Q: Q13) Cars A and B are travelling around the circular race track. At the instant shown. A has a speed…

A:

Q: Table Q1(a) shows the experimental values for a PVC pipe with diameter of 0.505 m under tensile…

A:

Q: Question 3 Determine the force (N) exerted on a 12.58-cm spring when it has a displacement of 3.81…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: vard and extend the arms while placing an object into the trunk of a car. Assum driver lifts a 60-lb…

A: A=90°V=0H=10inD=25inFM=1Ld, CM=0.95 RWLORG = 5110H1-0.0075v-300.82+1.82D(1-0.0032 A)xFMxCM RWLORG =…

Q: Water is the working fluid in a regenerative Rankine cycle with one closed feedwater heater and one…

A:

Q: It is observed that the skier leaves the ramp A at an angle OA = 30 degrees with the horizontal and…

A: Given data  VA = 21.8 m/s θA = 30 degrees g = 9.81 m/s2 To determine  a) Time of flight (tA-B) b)…

Q: Using the appropriate tables, determine the change in specific entropy between the specified states,…

A: The given information in the problem is shown in the following attached image:

Q: A force P of magnitude 550 lb acts on the frame shown at point E. Determine the perpendicular…

A:

Q: he 44-kg homogeneous smooth sphere rests on the 32° incline A and bears against the smooth vertical…

A:

Q: The 4-kg collar is attached to a spring that has an unstretched length of 2m and a stiffness k=10.1…

A: Given: The mass of the collar is, m=4 kg. The unstretched length of the spring is, l=2 m. The…

Q: A100 kg boy starts from rest at the bottom A of a 10-percent incline and increases his sneed at a…

A:

Q: 19. An engine runs on a rich mixture of methyl alcohol (CH O), ethyl alcohol (CHO) and air. The…

A: As given that methyl alcohol ,ethyl alcohol and air is used for the combustion reaction. The partil…

Q: Write down the conditions to obtain constant angular velocity ratio by double hool joint. Consider a…

A:

Q: The shape factor F2-1 is

A: Given data,  Solid sphere 1 of radius r is placed inside a hollow. Hemispherical surface 2 of raius…

Q: . Determine the gage pressure at point A (Figure P4.44) in kilopascals and in pounds per square…

A: As per the guidelines we are subjected to solve only one question at a time. Please repost the same…

Q: i.In a cyclic process heat transfer are +14.7 kJ, -25.2 kJ, -3.56kJ and +31.5 kJ. What is the…

A:

Q: The pulley at D is frictionless and the cylinder weighs 100 lb. a. Determine the vertical reaction…

A:

Q: 15 kip-ft Given are the following data in the figure. Determine what statement is correct if G is 12…

A:

Q: If the man at B exerts a force of P = 401lbs on his rope, determine the magnitude of the force F the…

A:

Q: Calculate the force in member BJ. 15 KN 10 KN 10 KN 20 KN A C. D 5.0 m H. G 4 @3.0 m 12.0 m O 20.41…

A:

Q: Find the reactions at the fixed connection at A. 4 N/m 2m 4m O NONE OF THE GIVEN CHOICES O RA = 24N;…

A:

Q: A golf ball is launched with the initial conditions shown in the figure. Determine the radius of…

A:

Q: For the body shown. At the instant shown, point B moves in straight line in y positive directi with…

A: There are two types of accelerations that are acting on a circular surface. One type of acceleration…

Q: skating is an example of

A: Answer:- sliding friction

Q: orientation for equilibrium. The forces are concurrent at point O. Take F= 15 kN. 12 kN 45 6 kN

A: To determine the force P and its direction.

Q: 2.5 kN 1.5 kN 3 kN 30 A B. 2m 4m 2m

A: Resolve the two forces along the beam and perpendicular to the beam as shown. Write the x component…

Mechanisms of heat transfer

Heat transfer is an essential discipline in thermal engineering that deals with the transfer, conversion, usability, and creation of heat or thermal energy. Transfer of heat occurs through various mechanisms like conduction, convection, radiation, and change of phases. All these mechanisms have distinct characteristics, but these mechanisms can simultaneously occur in an identical system.