ANSWER ASAAAP EVERYTHING Question 3Determine the force (N) exerted on a 12.58-cm spring when it has a displacement of3.81 inches. Note that the same spring has a change in length of 14.17 cm when appliedwith a force of 22.58 N. (Use 2 decimal places for the final answer.)DQuestion 4Consider two separate springs, spring A and B. Spring A has 13.3 times the stiffnessthan Spring B when Spring B has 11.23 times the change in length than that of Spring A.Determine the ratio of the amount force applied in Spring A to the force applied inSpring B. (Use 2 decimal places for the final answer.) DQuestion 123.26-cm spring is displaced by 19.3 cm when 21.04 N is applied. What would be theresulting final length of the spring (inches) when a tensile force of 43.51 N is applied?(Use 2 decimal places for the final answer.)Question 2The initial and final length of spring A are 17.65 cm and 48.61 cm respectively after aforce of 42.36 N is applied. If spring B with twice the stiffness and length is applied withtwice the force as compared to that of spring A, what would be the resulting change inlength (m) of spring B? (Use 4 decimal places for the final answer.)

“Since you have asked multiple questions, we will solve the first question for you. If you want any…

Question 3 Determine the force (N) exerted on a 12.58-cm spring when it has a displacement of 3.81 inches. Note that the same spring has a change in length of 14.17 cm when applied with a force of 22.58 N. (Use 2 decimal places for the final answer.)

Question 3 Determine the force (N) exerted on a 12.58-cm spring when it has a displacement of 3.81 inches. Note that the same spring has a change in length of 14.17 cm when applied with a force of 22.58 N. (Use 2 decimal places for the final answer.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Which among the following is a forming process in which thickness of the metal plate is decreased by…

A: Rolling: In this handle, the workpiece within the frame of slab or plate is compressed between two…

Q: Describe Pascal’s law?

A: Pascal’s law states that the static pressure acted on a liquid particle at rest is normally towards…

Q: %o change in diamefesx-?

A: Given; Solid cylinder of; diameter,d1=120 mmheight,h1=50 mmTwo frictionless flat dies to a…

Q: sketch the front, top, and right-side views of the objects shown in exercise 2.1 and 2.2.

A: The given question contains orthographic projections. Orthographic projections are the diagrams…

Q: 18. How far off from the center of the support is the center of the two holes in the bosses of the…

A: 18) Distance=4.2-0.66 =3.54 in

Q: What about the 100N weight?

A: There is a thin triangular plate in x-y plane.And location for the center of gravity is to be find…

Q: Figure shows a heat exchanger designed to cool 5250 kg/h of an ethyl alcohol solution (Cp = 3810…

Q: the parts of a micture can be using the physical properties of the compund

A: Compounds are substances made up of two or more elements whereas mixtures are made up of elements or…

Q: the effect of scratching the of the iron sheet surface with different objects

A: Effect of scratching the of the iron sheet surface with different objects.

Q: How would tou answer #10?

A: As mentioned in the question to solve #10, i will solve only question 10th

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: Please typing answer only IENG 302 - Manufacturing Processes: We are reducing the diameter of a…

A: Here I'm going to find all the answers.

Q: To make 5 cast iron tool holder as shown in Figure 2 on a one time order, and the inside hole…

A: Die casting and forging involves huge initial machine cost , it is not recommended to go for die…

Q: can you Reslove?

A: To solve the problem you have typed in, follow these steps: Analyze the given data:L2 = 6Q2 = 35…

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: A screwdriver is a kind of wheel and axel machine where the radius of the handle is the input…

A: Given data: The diameter of handle, d1 = 1 in. The diameter of the shaft, d2 = 1/4 in. Write the…

Q: Determine the natural frequency of the system by a) the Equivalent Mass and Equivalent Stiffness…

A: (a) Write the expression of kinetic energy conservation to write equivalent mass of the system.…

Q: Okay I did everything you did but the only thing I didn't do was take away 10 degrees from my…

Q: re did you get 1 for m from???

A: Given data as per questionInitially air containsFirst Phase1P1=30 lbf/in2T1=540°FV1=4 ft3Second…

Question

ANSWER ASAAAP EVERYTHING

D
Question 1
23.26-cm spring is displaced by 19.3 cm when 21.04 N is applied. What would be the
resulting final length of the spring (inches) when a tensile force of 43.51 N is applied?
(Use 2 decimal places for the final answer.)
Question 2
The initial and final length of spring A are 17.65 cm and 48.61 cm respectively after a
force of 42.36 N is applied. If spring B with twice the stiffness and length is applied with
twice the force as compared to that of spring A, what would be the resulting change in
length (m) of spring B? (Use 4 decimal places for the final answer.)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

can this be done using simpsons rule?
1
Question 1 An engineer first draws a circle in a plane and uses a tool to convert the circle to a disk that is 3 mm thick in SOLIDWORKS. The engineer most likely used the feature. Chamfer Fillet Hole Extrude
Gentlemen, please help to solve a,b,c as I faced confusing questions about screw jack. Conditions are: screw jack is lifting 3.2 tonnes, screw pitch is 12 mm, diameter of the screw is 5 mm. Coefficient of friction was not given but I think we will need it for total force calculation, lets take it 0.2. a) Calculate horizontal component to move the load - what is ment here by horizontal component? b) Calculate vertical component to move the load - what is ment here by vertical component? c) Total force needed to move the load with a lever of 0.82m d) Velocity ratio (VR=distance by effort/distance by load) Distance by effort (lever)=2 x 3.14 x 0.82 = 5.15m Distance by load = pitch= 12mm= 0.012 m VR=5.15/0.012= approx 429. e) Calculate efficiency. For this we need to have MA (mechanical advantage). It can be calculated when we know total force. Efficiency=Load (3200 x 9.8) / effort
Hello, I was just wondering how you find hte angle of the blocks to 45 degrees? Thank you!
Can You please check number 01? it is not 84.56 can you redo number 1?? v2??
what The answer 15 for this: 23,500 (1 + 0.031) 30 4.3/ number • answer must be report to the proper of significant digits A a showe all work Bea
thank you can u plz solve f&g now
It's saying this is not correct. Thank you for your help.
Question 6 a) The bore of each cylinder in a six-cylinder car engine is 45 mm and the stroke for each piston is 125 mm. calculate the cubic capacity of the engine in cubic centimetres (cm³); and calculate the clearance volume per cylinder for a compression ratio, r, of 8.75. b) The bore of each cylinder in a four-cylinder four-stroke internal combustion engine is 38 mm and the stroke of each piston is 165 mm. During testing, the engine runs at 180 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 3.4 cm² and a diagram length of 1.2 cm. The pressure scale on the indictor diagram is set to 150 kN/m² per cm. Calculate the mean effective pressure (m.e.p) and the indicated power developed by this four-cylinder four-stroke engine. c) Figure Q6c shows a pulley system with a suspended load w of 2000 N. Calculate the following: (i) (ii) (iii) (iv) The effort force (FEffort) necessary to lift and hold a load of 2000 N. The ideal mechanical advantage…
3d
what type of grinding wheel should be used to get the required finish on this part using a surface grinder?