DATA AND RESULTS:SOLVE FOR ITS FINENESS MODULUS AND % ORGANICMATTERSIEVE SIZEWT. RETAINED% WT. RETAINEDCUMULATIVE % OFRETAINED#4#833.3# 1697.7# 30620#5095.7# 10027.9PAN31.5

Answered: Image /qna-images/answer/c6d0185e-2fd0-481b-8da5-dde3e7ec9350.jpg

Answered: DATA AND RESULTS: SOLVE FOR ITS…

DATA AND RESULTS: SOLVE FOR ITS FINENESS MODULUS AND % ORGANICMATTER WT. RETAINED CUMULATIVE % OF RETAINED SIEVE SIZE % WT. RETAINED #4 #8 33.3 #16 97.7 #30 620 #50 95.7 #100 27.9 PAN 31.5

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The specific gravity and absorption test (ASTM C128) were performed on fine aggregate. The following data were obtained.Given:Mass of SSD sand = 450.0 gMass of pycnometer with water = 550 gMass of pycnometer with water plus sand = 840 gMass of dry sand = 446.5 gRequired:a) bulk dry specific gravityb) bulk SSD specific gravityc) apparent specific gravityd) absorption, in percente) free moisture if the sand in the stockpile has a moisture content of 5%.
1. Compute individual percent retained, cumulative percent retained and percent passing. 2. Make a particle size distribution chart using semi log using excel. 3. Compute the fineness modulus of the sample. 4. Identify whether weight percent within the governing specs passed.
Define Berardi et al. (1991) Modulus Reduction ?
A severe weathering clay brick was tested for absorption and saturation coefficient according to ASTM C67 procedure and produced the following data:dry mass of specimen = 2.186 kgsaturated mass after 24-hr submersion in cold water = 2.453 kgsaturated mass after 5-hr submersion in boiling water = 2.472 kgCalculate absorption by 24-hr submersion, absorption by 5-hr boiling, andsaturation coefficient. Does the brick satisfy the ASTM requirements?
Q-5) Answer (True) or (false) and correct if (false). 1. C,S need more than twice amount of water from C,S to hydration. 2. Calcareous material as a source of silica and alumina in manufacture of Portland cement. 3. Rough surfaces of aggregate improve mechanical bond. 4. Saturated surface dry condition (SSD) of aggregate means all internal pores are saturated with water and its surface wet. 5. Iraqi specification No. 5 limited Sulfur oxide in the cement as max. by 2.8% when C3A > 5%.
For a given sieve analyis: No. 4 - % finer 99%, for No. 200 -%finer 76. LL=60, PL=32. Classify the soil using USCS. Justify your answer. O a. MH O b. CH O c. OOL O d. CL
what are the different classification of water hardness?
Analysis of Fine AggregatesFill in the table:
2. Given the sieve analysis results shown in the table, answer questions below. Fine Sieve Initial Wt. 563 Accum. Wt. 3/8" #4 42.1 #8 169.6 #16 276.1 #30 350.1 #50 398.3 #100 429.6 #200 453.6 a) Calculate percent retained, cumulative percent retained, and percent passing of each sieve size b) Calculate Fineness Modulus, does it meet the typical range? c) Does this aggregate meet ASTM C33 grading requirement for fine aggregate? Please provide the grading limit you used. (
Discuss the results in the following graph?
1. Compute individual percent retained, cumulative percent retained and percent passing. 2. Make a particle size distribution chart using semi log using excel. 3. Compute the fineness modulus of the sample. 4. Identify whether weight percent within the governing specs passed.
A saturated aggregate sample with an absolute volume of 5.05x10^-5 m^3 has a mass of 178 g before drying and 139 g after drying in an oven. Assume the water absorption by volume to be 59.18%. Determine the following: a. Specific gravity of the solid particles b. Mass specific gravity c. Void Ratio d. Porosity