d. Suppose that the cylindrical tank in the accompanying figure is filled to a depth of 4 feet at time t = 0 and that the water discharges from a hole at the bottom of the tank at the rate shown below. How many minutes will it take for the tank to drain completely? discharge flowrate = 0.025 √h, ft³/sec 4 ft 1 ft

d. Suppose that the cylindrical tank in the accompanying figure is filled to a depth of 4 feet at time t = 0 and that the water discharges from a hole at the bottom of the tank at the rate shown below. How many minutes will it take for the tank to drain completely? discharge flowrate = 0.025 √h, ft³/sec 4 ft 1 ft

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

South Africa's largest dam is the Gariep Dm located in the Free State. The actual depth of water behind the Gariep Dam is about 90 m. a) Do you think the dam wall thickness is the same at a depth of 1 meter as it is at a depth of 90 meters? b) What is the actual water pressure at the base of this dam? Maximum number of characters (including HTML tags added by text editor): 32.000 Show Rich-Text Editor (and character count) 18°C Cloudy ^ O ENG DELL Insert Delete F12 PrtSc F10 F11 F9
A viscous fluid flows in two different pipes. Pipe 1 has a radius r1, and Pipe 2 has a radius r2. If both pipes have the same length and r1 > r2, choose the correct statement about the pressure difference of the fluid in Pipe 1 and Pipe 2 The pressure difference of the fluid is the same in Pipe 1 and Pipe 2. The fluid in Pipe 1 has larger pressure difference. It cannot be determined in which pipe the fluid has larger pressure difference. The fluid in Pipe 2 has larger pressure difference.
In figure 8, we found that the speed of water at point 1 increased from 2.01 m/s at 23 cm to 29.8 m/s at 40 cm going from point 1 to point 2. Calculate the pressure in position 1, given that the absolute pressure in point 2 is 2.06x10 N/m2 (atmospheric, as it must be). Zxp A, dv dx, V2 A, dV Y1 FLOW Figure 8
A large open tank contains water as shown in the figure. The level of the water in the tank is 8 m from the ground while the circular opening in the side of the tank is 1.5 m above the ground. If the discharge rate at the opening is 75 li/sec, determine the diameter of the opening. 1
A very large water tank, open at the top, has a small hole in the bottom. Assume that the area of the hole is much much smaller than the area of the top of the tank. When the water level is 34.6 m above the bottom of the tank, what is the speed of the water leaking from the hole? Express your answer in m/s, to at least one digit after the decimal point.
Calculate the absolute pressure at an ocean depth of 1.0 km. Assume that the density of Water, Pwater is 1.025 x 103 kg/m³ and the atmospheric pressure, Patmosphere= 1.01 x 10 Pa. (Use: Acceleration due to gravity, g= 9.8 m/s²) elect one: a. 1.01 x 107 Pa b. 1.02 x 106 Pa c. 1.11 x10$ Pa
A Venturi tube narrows down from the inlet section to the throat. The inlet is 7 ft^2 while the throat area third of the inlet. What is the rate of flow of water when the change in pressure is 0.85 atm? What is the velocity of test and throat section? (English Units) *
The intake in the figure has cross-sectional area of 0.84m ^ 2 and water flow at 0.35 m/s . At the outlet, distance D = 170 m below the intake, has a cross-sectional area of 0.031m ^ 2. What is the flow speed at the outlet? What is the pressure difference between inlet and outlet?
A tank holds a large amount of water. A pipe is connected to the tank at the upper end and is open to the air at the lower end (see figure).The upper end of the pipe has a diameter of 17.0 cm. The lower end of the pipe has a diameter of 8.60 cm. The speed of the water at the upper end is 2.00 m/s.What is the flow rate of the water in the pipe?
Air P = 76 kPa SG₁ = 13.55 40 cm 22 cm Consider a dual-fluid manometer attached to an air pipe as shown in the image. If the SG of one fluids is 13.55, determine the SG of the other fluid for the indicated absolute pressure of air. Take the atmospheric pressure to be about 100 kPa. SG₂
A pumped fluid distribution system is being designed to deliver Q=200 gal/min of water to a cooling system in a power generation plant. Read the corresponding flow areas in m2 of discharge line Ad from Appendix F _________ A. 3.090 x 10^-3 m^2 B.1.314 x 10^-3 m^2 C.4.768 x 10^-3 m^2 D.2.168 x 10^-3 m^2
2. A fluid moves in a steady flow manner between two sections in a flow line. At section 1 area is equal to 10 square foot speed is equal to 100 feet per minute, specific volume is equal to 4 cubic foot per pound. At section 2, area is equal to 2 square foot, density is equal to 0.20 pound per cubic foot. Calculate the mass flow rate (lb/min) and the speed and section 2 (fps).