You fill a 7.0 x 10-3 m3 bucket with water that flows from a pipe of radius 1.30 cm. If it takes 48.0 seconds to fill the bucket, what is the average flow speed within the pipe? [Answer in units of m/s, with 3 sig digits, but do not enter units with your answer] Your Answer: Your Answer

You fill a 7.0 x 10-3 m3 bucket with water that flows from a pipe of radius 1.30 cm. If it takes 48.0 seconds to fill the bucket, what is the average flow speed within the pipe? [Answer in units of m/s, with 3 sig digits, but do not enter units with your answer] Your Answer: Your Answer

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

A cylindrical tank with a large diameter is filled with water to a depth D = 0.461 m. A hole of cross-sectional area A = 7.44 cm² in the bottom of the tank allows water to drain out. (a) What is the rate at which water flows out, in cubic meters per second? (b) At what distance below the bottom of the tank is the cross-sectional area of the stream equal to one-half the area of the hole? (a) Number i (b) Number i Units Units
1. Fluid Flow: Water runs into a fountain, filling all pipes, at a steady rate of 0.750 cubic meters per second. How fast will it shoot out of a hole 4.50 cm in diameter?
Density of fluid : 1 x 10 kg/m^3 Diameter of hose : 2 cm A tank of waste water is being emptied by means of siphon if the wastewater travels downward by the distance indicated and the tank is emptied in 250s what volume of wastewater is in the tank?
Consider the hydraulic lift shown in the figure. The small piston has an area Aj of 0.0330 m², and the large piston has an area A, of 4.00 m?. What force F2 will the large piston provide if the small piston is pushed down with a force F, of 18.0 N? Assume that the fluid used in the lift is incompressible. F, = F, y2 A, A, F,
A cylindrical tank with a large diameter is filled with water to a depth D = 0.273 m. A hole of cross-sectional area A = 5.03 cm² in the bottom of the tank allows water to drain out. (a) What is the rate at which water flows out, in cubic meters per second? (b) At what distance below the bottom of the tank is the cross-sectional area of the stream equal to one-half the area of the hole? (a) Number i (b) Number i Units Units
A force of 470 N is exerted on the pedal cylinder of an automatic hydraulic system. The pedal cylinder has a diameter of 0.425 cm. How much pressure is transmitted in the hydraulic system? Express your answer in atmospheres. atm
A cylindrical tank with a large diameter is filled with water to a depth D = 0.235 m. A hole of cross-sectional area A = 6.96 cm2 in the bottom of the tank allows water to drain out. (a) What is the rate at which water flows out, in cubic meters per second? (b) At what distance below the bottom of the tank is the cross-sectional area of the stream equal to one-half the area of the hole?
The diameters of the pistons on a hydraulic press are 5.0 cm and 40 cm. When a force of 50 N is exerted on the smaller piston, what force can the larger piston exert? {A = Bd2/4}Answer is in Newton
If a kitchen sink has a volume of 20 L. Water flows in the sink with a mass flow rate of 0.5 kg/s. If the drain is closed, how long, in seconds, does it take for the sink to fill up? Density of water = 1000 kg/m3
7) The equation resultant wave from the superposition of two waves propagating in opposite directions is: y = 0.4 sin (2nx) Cos (2at) Knowing that the considered medium is formed of 3 nodes, determine the positions of this 3 points, assuming that one end is the point x=0: A x = 0 m, x2= 2m, X3=4m, B-x, = 0 m, x3= 1m, *3 = 2m, C- x1=0 m, x2= 0.75m, x3 = 1. 5m, D- x= 0 m, x2 = 0.5 m, x3= 1m, E- x, = 0 m, x2= 0. 25 m, X3 = 0. 5m. O A В C O D E
A very large water tank, open at the top, has a small hole in the bottom. Assume that the area of the hole is much much smaller than the area of the top of the tank. When the water level is 34.6 m above the bottom of the tank, what is the speed of the water leaking from the hole? Express your answer in m/s, to at least one digit after the decimal point.
A cylindrical tank with a large diameter is filled with water to a depth D = 0.278 m. A hole of cross-sectional area A = 7.04 cm2 in the bottom of the tank allows water to drain out. (a) What is the rate at which water flows out, in cubic meters per second? (b) At what distance below the bottom of the tank is the cross-sectional area of the stream equal to one-half the area of the hole?