Answered: d) Overhead Transmission Lines are…

d) Overhead Transmission Lines are preferred for Transmission of Power for Long Distances, why? e) Alternating Current is preferred over Direct Current in Power System, Why?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.2MCQ: Overhead transmission-line conductors are bare with no insulating cover. (a) True (b) False

See similar textbooks

Related questions

Q: Explain the concept of load shedding in the context of power systems.

A: According to the question, we need to explain the concept of load shedding in the context of power…

Q: A transmission line that has a resistance per unit length of 5.40 x 10-40 /m is to be used to…

A: Transmission line- Transmission Lines are the connection between the Generation busbar and the…

Q: Obtain the per-unit equivalent circuit for the following one-line diagram in Figure 1. Xine = 100 Q…

Q: Assume that a 5 mile long feder is supplying a 2000 kVA load of increasing load density starting at…

A: It is given that: l=5 miS=2000 KVAK=0.00001 % VD/KVA.mi

Q: Match the items in List - I with the items in List - II and select the correct answer using the…

A: The list in the table,

Q: One-line diagram of a power system is shown below. Relevant details are mentioned below. Generator:…

A: Consider the generator rating as a base. The generator rating is given as 100 MVA and 11 kV. For the…

Q: How does the concept of microgrids contribute to enhancing the resilience and efficiency of modern…

A: A microgrid is a localized, self-contained electrical system that can generate, store, and…

Q: e = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase…

A: 1)It is not possible that , current can flow in two directions at same time. However if we apply two…

Concept explainers

Short Transmission Line

A short transmission line is a transmission line that has a length less than 80 kilometers, an operating voltage level of less than 20 kV, and zero capacitance effect.

Power Flow Analysis

Power flow analysis is a topic in power engineering. It is the flow of electric power in a system. The power flow analysis is preliminary used for the various components of Alternating Current (AC) power, such as the voltage, current, real power, reactive power, and voltage angles under given load conditions and is often known as a load flow study or load flow analysis.

Complex Form

A power system is defined as the connection or network of the various components that convert the non-electrical energy into the electric form and supply the electric form of energy from the source to the load. The power system is an important parameter in power engineering and the electrical engineering profession. The powers in the power system are primarily categorized into two types- active power and reactive power.

Question

d) Overhead Transmission Lines are preferred for
Transmission of Power for Long Distances, why?
e) Alternating Current is preferred over Direct
Current in Power System, Why?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
a. i. Why do power systems operate in an interconnected arrangement? ii. How is the frequency controlled in a power system? iii. What is meant by the stiffness of a power system? b. Two 50 Hz power systems are interconnected by a tie-line, which carries 1000 MW from system A to system B, as shown below. After the outDage of the line shown in the figure, the frequency in system A increases to 50.5 Hz, while the frequency in system B decreases to 49 Hz. i. Calculate the stiffness of each system. ii. If the systems operate interconnected with 1000 MW being transferred from A to B, calculate the flow in the line after outage of a 600 MW generator in system B. 1000 MW A В
What are FACTS (Flexible Alternating Current Transmission Systems) devices, and how do they enhance the control and stability of power systems?
The one line diagram of power system is shown in Figure Q.1. Use a commonbase MVA of 100 MVA and base voltage of 230 kV at the transmission line. Findthe p.u values to be used for the transformer and generator reactances.
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
Consider the single-line diagram of the power system shown in Figure 3.38. Equipment ratings are Generator 1: 1000MVA,18kV,X=0.2perunit Generator 2: 1000MVA,18kV,X=0.2p.u. Synchronous motor 3: 1500MVA,20kV,X=0.2p.u. Three-phase -Y transformers T1,T2,T3,T4,: 1000MVA,500kV,Y/20kV,X=0.1p.u. Three-phase YY transformer T5: 1500MVA,500kV,Y/20kVY,X=0.1p.u. Neglecting resistance, transformer phase shift, and magnetizing reactance, draw the equivalent reactance diagram. Use a base of 100 MA and 500 kV for the 50-ohm line. Determine the per-unit reactances.
a.Why does power plants have high amounts of voltages? Explain. b.Is it safe for transmission lines to have high current instead of high voltage? Why? c.What phenomenon is avoided by having separations between three conductor phases? Explain this phenomenon.
High Voltage level in Transmission system ensures ………………… a. High current in Overhead conductors b. Less power factor c. Low Power Transfer d. Reduction in conductor size
1. How do you measure three phase line currents by using two current transformers? Draw the connection scheme.
One-line diagram of a power system is shown below. Relevant details are mentioned below. Generator: 100 MVA, 11 kV, 3-phase, reactance 20%; Transformer T1: 100 MVA, 10/132 kV, reactance 6%; Transformer T2: 80 MVA, 132/10 kV, reactance 5%; Line reactance is 100 Q. Motors M1 and M2 are rated at 50 MVA and 40 MVA respectively both at 10 kV and 20% reactance. In the above, reactances are per-phase values. Taking generator rating as base, draw the per- phase impedance diagram in which the elements need to be expressed in per unit. * T1 M, Transmission Line G M2) A
Explain single line diagram for industrial power system
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --