D 8.14 It is required to design an NMOS differential amplifier to operate with a differential input voltage that can be as high as 0.1 V while keeping the nonlinear term under the square root in Eq. (8.23) to a maximum of 0.05. A transconductance g of 1 mA/V is needed. Find the required values of Vor» I, and W/L. Assume that the technology available has µ,C. A, results when R, = 10 kN? Assume 1 = 0. What is the resulting output signal corresponding to va at its maximum 200 µA/V?. What differential gain OX V id value?

D 8.14 It is required to design an NMOS differential amplifier to operate with a differential input voltage that can be as high as 0.1 V while keeping the nonlinear term under the square root in Eq. (8.23) to a maximum of 0.05. A transconductance g of 1 mA/V is needed. Find the required values of Vor» I, and W/L. Assume that the technology available has µ,C. A, results when R, = 10 kN? Assume 1 = 0. What is the resulting output signal corresponding to va at its maximum 200 µA/V?. What differential gain OX V id value?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Please answer this question and show necessary steps to obtain the answer.
Note: Please do not handwritten.
I need some assistance with this problem. I would like to have a step by step format for better understanding. Thanks
Questions Derive the Vps equation as a function of VGs, for the following MOSFET based amplifier. Please use current equations of MOSFET, as discussed in the class. As per class discussion, we know this circuit can be used as an AC amplifier. Please discuss how can the gain of this AC amplifier, be enhanced. Vp Iny Rp Vps VGs
For amplifier design, consider a very large load resistance RL . Use a 15 V DC source and a sinusoidal input signal of 200 mVpp and 1 kHz. Hint: you can start by choosing a collector (Icq) or drain (IDQ) operating current between 5 mA and 10 mA. 1. Design an input stage with a common drain amplifier that complies with thefollowing specifications: Voltage gain greater than or equal to 1 (Av1 ≥ 1). Input impedance greater than or equal to 250 kΩ (Zi1 ≥ 250 kΩ). Output impedance less than or equal to 2 kΩ (Zo1 ≤ 2 kΩ). Low cut frequency less than or equal to 20 Hz (fcb1 ≤ 20 kHz). Use a 2N3819 (NTE312) transistor.
a. Design a series Fed Class A amplifier using a silicon transistor with beta value 25 which gives power dissipation of 12.75 watts supplied with 25 volts battery to produce an input power of 15 watts. Also find its efficiency and output power. Given Q point at 12V, 0.5A. b. Simulate the circuit inserting the design values by applying peak input base current of 12mA and display the output waveform.
Design a feasible class A silicon BJT Power Amplifier that provides a high voltagegain using 15 volts supply and employs a concept to increase its loaded efficiency to50% so that little power loss is provided at the collector terminal.Given by manufacturer for safe operation, the amplifying component has a DCcurrent gain of 200 and a collector current limit of 4mA. The output stage of theAmplifier drives a headphone with 32-ohms load impedance applicable forsmartphones.
3 I only need the answer
Q (i) Sketch a feasible class A silicon BJT Power Amplifier that provides a high voltage gain using 15 volts supply and employs a concept to increase its loaded efficiency to 50% so that little power loss is provided at the collector terminal. Given by manufacturer for safe operation, the amplifying component has a DC current gain of 200 and a collector current limit of 4mA. The output stage of the Amplifier drives a headphone with 32-ohms load impedance applicable for smartphones. (ii) Use a DC load-line to graphically find the three operating points of the amplifier. (iii) On the load line, sketch the respective AC signal at each operating point of the amplifier during its dynamic condition.
Please help answer the question shown below. The topic is Electronics. Any help will be much appreciated. Thank you!
1. What is the transconductance or gm of an amplifier? What role does it play in an amplifier circuit? Two amplifier circuits have a gm of 6mA/V and 3mA/V respectively. Draw the ip VGs characteristics and the input and output waveforms of these two circuits. Which of the output has a higher amplitude? Explain graphically from the ip- VGs plot.
Question: please help, Design a common source (CS) amplifier to have a voltage gain of -25V/V when the drain current needs to be ID=0.5 mA, the load resistance R=18 k, and the source resistance R,=5 kN. The amplifier needs to amplify a signal of amplitude 20 mV. The circuit is powered from a 15 V DC source. The available MOSFET transistor has a threshold voltage V=1V, kn=4mA/V?, and Va=100 V. Show all your calculations and circuit diagrams for both DC and small signal analysis. Make simplifying assumptions in your calculations.