D 4 ft 150 lb 4 ft -3 ft -3 ft Prob. 6–92

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Answer Let us first draw ILD for member DI. In order to draw Influence line diagram(ILD) for member…

Q: Determine the tension at AC and reaction at B on the structure shown.

A:

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Answer  Let us first draw the ILD for member DI. Pass a section through member DI as shown below…

Q: ituation 2: Determine the forces in cables AC and AB needed to hold the 20-kg ball D in equilibrium.…

A: GIVEN- Mass of the ball D = 20kg Force F =300N

Q: M1 = 4000 N/m M2 = 9000 N/m P = 3600 N (downward) w1= 800 N/m (downward) w2 = 600 N/m (downward)…

A:

Q: The hoist supports the 150-kg engine. Determine the force in members DB and FB. Also determine the…

A:

Q: Use the portal method and determine (approximately) the reactions at supports A and B. YkN XKN A 5 m…

A:

Q: Assume that the loads are being transmitted to the bottom of the truss in the diagram below. For…

A: Answer  (a) Influence line diagram for member DI Consider a section passing through member DI as…

Q: The

A:

Q: 1. Forces P and F acting along the bars maintain equilibrium of pin A. Determine the values of P and…

A:

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Solution  ILD for member DI  Pass a section through member DI as shown below When the Unit load is…

Q: Analyze the statically determinate planer force system to calculate the reactions at the supports.…

A:

Q: The beam supports a uniform dead load of 500 N/m and a single live concentrated force of 3000 N.…

A: Given Data  Dead load = 500 N/m  Concentrated Live load = 3000 N  Find  a. Maximum positive moment…

Q: 2. For the truss shown in the figure below, assume that the loads are being transmitted to the…

A:

Q: Situation 2 | Beam ABCDEFG below is subjected to multiple loads as show. The total length of the…

A: Given:- L=10mABCDEFG beamTo find:-shear equation for segment B_Cmoment equation of segment C-D

Q: 6 kN/m 10 kN B 3 m -1.5 m- -1.5m-

A: Joint A  Vertical reaction Va Horizontal reaction Ha Joint C  Vertical reaction Vc Horizontal…

Q: The beam is subjected to a uniform dead load of11.2 kN/m and a single live load of 52 kN. Determine…

A:

Q: at C. Determine the reaction forces of the roller at A, the hinge at B and the fixed support lk / H…

A:

Q: A uniform live load of 0.25k/ft. and a single concentrated live force of 3 k are to be placed on the…

A:

Q: Use the method of members to determine the horizontal and vertical forces at the supports A and E…

A: free body diagram of ABC

Q: The beam supports a uniform dead load of 500 N/m and a single live concentrated force of 3000 N.…

A: Given data in question  Live load Dead load Span member length  To find out  Maximum moment at point…

Q: d live load of P kN. Determine (a) the maximum positive (upward) reaction at B, (b) the maximum…

A: For the above beam, Assume W1=87N/mW2=4kN/mP=3kN

Q: H J K "d" kN "d" kN "c" kN "b" m G В "a/2" m "a" m 6 @ "a" m = 6*a m

A:

Q: Determine the reactions at the pin A and the tension in cord BC. Set F = 40 kN. Neglect the…

A:

Q: Determine the internal moment in the beam at Ⓒ. Assume is a roller and is a pin. El is constant.

A:

Q: Determine the moments at B and C, then draw the moment diagram for the beam. All connections are…

A: Given- To find-Determine the moments at B and C, then draw the moment diagram for the beam. All…

Q: Determine the reactions at the supports A and B of the compound beam. Assume there is a pin at C.…

A:

Q: Determine the resultant force at pins A, B, and C on the three-member frame. P=129 N q=200 N/m

A: Load P = 129 NLoad intensity q = 200 N/m

Q: A pin and two rollers support bars ABC and CD. A hinge at C connects the bars. The distributed…

A: Given Data -

Q: 3. Resolve P = 480-N force into components along the cables AB and AC. Use a=40• and B=25°. B C

A:

Q: Compute the reactions at A and D. Determine the internal forces in each member of the truss using…

A:

Q: a. Maximum tension on member DI in kN, put "O" if none. b. Maximum compression on member DI in kN,…

A:

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Answer  ILD for member DI  Pass a section through member DI as shown below When Unit load is at A…

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: A truss with hinged support at G and roller support at C is given. To this, a train of load moves…

Q: FIODICH INO. 2 The frame shown below is subjected to the load of 1.5 kip. For the pins at A and B…

A:

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.