Current Attempt in Progress A hollow steel shaft with an outside diameter of 125 mm and a wall thickness of 18 mm is subjected to a pure torque of T=7,200 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: (a) Tmax = i MPa (b) dmin = i mm

Current Attempt in Progress A hollow steel shaft with an outside diameter of 125 mm and a wall thickness of 18 mm is subjected to a pure torque of T=7,200 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: (a) Tmax = i MPa (b) dmin = i mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stresses at a point in a bar are o1 = 28N/mm2 (tensile) and o2=12N/mm2 (compressive) as shown in Figure (a) Determine the normal, tangential and resultant stress in magnitude and direction on a plane inclined at 55° to the axis of the major stress. (b) Determine the maximum intensity of shear stress in the material at the point. (c) Also, solve the same problem using Mohr's circle method and compare the results. O2 Axis of Major Stress 55°
Q-1 A circular bar is to withstand a bending moment of 10 kNm and a torque of 30 kNm. Determine the diameter of the bar if the yield stress of the material is 250 MPa and the factor of safety is 3. Use maximum normal strain theory of failure. Take Poisson's ratio as 0.3.
Find the value of maximum principal stress if maximum shear stress is 60 MPa and minimum principal stress is 50 MPa
UPVOTE WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. SOLVE IN 2 DECIMAL PLACES. BOX THE FINAL ANSWERS.
The bronze bar 3 m long with a cross-sectional area of 350 mm2 is placed between two rigid walls. At a temperature of -20°C, there is a gap A = 2.2 mm, as shown in the figure. Find the temperature at which the compressive stress in the bar will be 30 MPa. Use a = 18.0x 10-6 / °C and E = 80 GPa. 3 m-
A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank is 165mm and the wall thickness is 15mm. If the air in the tank is pressurized to 18.0MPa, determine: (a) the longitudinal and hoop stresses in the wall of the tank. (b) the maximum shear stress in the plane of the cylinder wall. (c) the absolute maximum shear stress on the outer surface of the cylindrical wall. Answers: MPa MPa MPa MPa (a) Olong= Thoop= (b) Tmax= (c) Tabs max= Mi i i i
A solid 2.95 in. diameter shaft is subjected to a torque of T = 305 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point Hon the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. N Answer: (a) Op1= i Op2= i A Tmax in-plane i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
A metal block (E = 60 GPa and Poisson's ratio of 0.35) rests on a rigid surface as shown below. It has uniformly applied loads which results in uniform stresses on the surfaces as shown. Assuming a compressive stress of 200 MPa along x-direction, determine the magnitude of stress oy for which the change in the height of the bock will be zero, (b) the corresponding change in the area of the face ABCD, and (c) the corresponding change in the area of the volume of the block. 40 2 100mm 25mm
4 A metal wire Im long and of 10mm diam eter is stretched by a load of 50 kg. If E = 7 x 10³ N/mm² for the metal, find the (a) stress (b) strain and (3) Poisson's ratio if the lateral strain is 2.6x 105 m/m.
S=25
i need the answer quickly
#4 will upvote anyone who will answer