Q-1 A circular bar is to withstand a bending moment of 10 kNm and a torque of 30 kNm. Determine the diameter of the bar if the yield stress of the material is 250 MPa and the factor of safety is 3. Use maximum normal strain theory of failure. Take Poisson's ratio as 0.3.

Q-1 A circular bar is to withstand a bending moment of 10 kNm and a torque of 30 kNm. Determine the diameter of the bar if the yield stress of the material is 250 MPa and the factor of safety is 3. Use maximum normal strain theory of failure. Take Poisson's ratio as 0.3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find principal stresses and max in plane shear stresses ...using stress transformation equation
Static Method of Analysis The plastic modulus of a section is 4.8 x 10-4m³. The shape factor is 1.2. The plastic moment capacity of the section is 120 kN-m. The yield stress of the material is A 100 MPa B 240 MPa C 250 MPa D 300 MPa
(A) he figure below shows three metal cubes A, B, C of side 100 mm in direct contact, resting on a rigid base and confined in x-coordinate direction between two rigid end plate. If the upper face of the center cube B is subjected to uniform compressive stress of 0.5 kN/mm², compute for cube B, the following: (i) The direct stress in x-direction (₂) (ii) The direct strains in the three coordinates directions x, y and z (iii) The volumetric strain Rigid A E=150 kN/mm² μ = 0.25 o₂ = 0.5 kN/mm² B E = 200 kN/mm² μ = 0.3 -Rigid C E = 150 kN/mm² μ = 0.25 Rigid
A metal block (E = 60 GPa and Poisson's ratio of 0.35) rests on a rigid surface as shown below. It has uniformly applied loads which results in uniform stresses on the surfaces as shown. Assuming a compressive stress of 200 MPa along x-direction, determine the magnitude of stress oy for which the change in the height of the bock will be zero, (b) the corresponding change in the area of the face ABCD, and (c) the corresponding change in the area of the volume of the block. 40 2 100mm 25mm
4 A metal wire Im long and of 10mm diam eter is stretched by a load of 50 kg. If E = 7 x 10³ N/mm² for the metal, find the (a) stress (b) strain and (3) Poisson's ratio if the lateral strain is 2.6x 105 m/m.
A solid circular column is 3 meters long. It is fixed at the bottom and pinned at the top. The Youngs modulus of the material is 70 GPa and the maximum allowable stress is 25 MPa. Using a factor of safety of 2.5 in calculating Eulers critical load: i. Determine the dimensions of the cross section if the column is to safely support a 100 kN load. i. Confirm the normal stress developed in the column and comment on the result.
Give me right solution according to the question.
Problem 2: A one inch diameter machined steel cantilever 10 in. long is loaded on the end with a force that varies from 60 lb down to 100 lb up. There is a "fillet where the member is connected to the support which causes a theoretical stress concentration factor K+ = 1.32. The notch sensitivity factor q may be taken at 0.92. If the material has an ultimate stress s= 80,000 psi, an endurance limit in reversed bending s= 35,000, and a yield strength, s,= 60,000, determine: (a) maximum bending stress, (b) minimum bending stress, (c) mean stress, (d) variable stress, (e) design factor N.
Sketch Mohr circle for the shown element. Use Mohr Circle to determine the normal stresses On and Ot and the shear stress Tat at this point if they act on the rotated stress element shown. Verify your results (On, Ot, Tat) using stress transformation eqns. 1,100 psi Tnt 1,750 psi On 20° 2,900 psi Illustrate the following on Mohr circle: center of Mohr Circle, reference point A, principle stresses, max in-plane shear stress, orientation of principal stresses Op1 and Op2, orientation of max in-plane shear stress,Os )
#4 will upvote anyone who will answer
i need the answer quickly
Shafts A and B are made of the same material and have the same cross-sectional area, but A has a circular cross section and B has a square cross section. Determine the ratio of the maximum shearing stresses occurring in A and B (i.e., TA), respectively, when the two shafts are subjected to the same torque (TA= TB). Assume both deformations to be elastic. Refer to Table 3.1. 92 TA TB The ratio of the maximum shearing stresses occurring in A and B is 1.356