Continuous foundation transmits 4 column loads. Each column transmits a load of 350 kN, the two terminal columns are at the end of the space boundary. All columns have a square section with a side of 0.5 m and the net distance between one column and another is 3.5 m. Soil bearing capacity is 80 kPa. So the required width of the base will be *

Q: Determine total indeterminacy and external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+2=5Number of member (m)=8Number of joint…

Q: Can you add the datum line in the illustration and make a bettter illustration based on solution

A: Given, Angle made by nozzle = 45o Horizontal distance = 15 to 20 m

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: What do you mean by the Bulk Richardson Number (BRN)?

A: The Bulk Richardson Number is defined as the ratio of turbulence due to kinetic energy to the shear.

Q: The ∑ F proceeding in the couple is?

A: Brief concept- Couple- It is a pair of equal and opposite parallel forces. These two forces do not…

Q: x; ]] a» a» dz || X2 a3 a a33

A: For calculation assume,

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: Fo B - P 800 mm C -600 mm

A:

Q: entify the outfall entify the peaks entify the valleys

A: Watershed: A watershed depicts an area of land that contains a typical arrangement of streams and…

Q: For the given structures, determine the degree of indeterminacy. 6. T 6

A: The given beam has three support conditions. The Left end is a Fixed support.(3 reactions)…

Q: at state of given (All in The Stres point is MPa) 80 100 100 i) And Principal Stren & Principal…

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: 05 Find the XT 0.5 1.5 3 2.5

A:

Q: aSN 200 mm 350 mm

A: Free Body Diagram (FBD):

Q: Draw the influence lines for the vertical and horizontal reactions, Ax and Ay, at support A and the…

A: Question consist of truss supported at hinge support at A and G . Length of members are given in the…

Q: 80 mm -L- В D 60 mm

A:

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: show the (c)

A:

Q: Q4: Convert the following into required: 1- An area 4.2 cm on amap with scale 1/5000 > Don , Olk,…

A:

Q: Explnation of EPDM.

A: The ethylene propylene diene monomer is abbreviated as EPDM.

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: Figure 2. Inside perimeter Outside perimeter Centreline

A: Inside perimeter :Length×2+Breadth×2+2×2'+3'24'3''×2+12'×2+2×2'+3'=79'6''

Q: 100 N 100 N 100 100 150 250

A:

Q: Y

A:

Q: Links CF connects members AD and EG. The two vertical links having a rectangular cross-section…

A:

Q: Explain why wx = 2/3(9-x)

A: Given:Required:To explain loading intensity for 6<x<9

Q: For the truss shown, determine the stress in members DC and DG. The area of each member is 800 sq.…

A: Given data: Area of each member is 800 mm2.