Links CF connects members AD and EG. The two vertical links having a rectangular cross-section measuring 5mm x 25mm are made of steel with allowable tensile strength of 500 MPa. The pins at C and F measures 16-mm and are made of steel with allowable shearing strength of 100 MPa. What is the over-all factor of safety for the links CF and the pins connecting them to the horizontal members?

Links CF connects members AD and EG. The two vertical links having a rectangular cross-section measuring 5mm x 25mm are made of steel with allowable tensile strength of 500 MPa. The pins at C and F measures 16-mm and are made of steel with allowable shearing strength of 100 MPa. What is the over-all factor of safety for the links CF and the pins connecting them to the horizontal members?

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter8: Eccentric Connections

Section: Chapter Questions

Problem 8.2.4P

See similar textbooks

Similar questions

A tie member of a roof truss consists of 21SA 100 x 75 x 8 mm. The angles are connected by fillet weld as shown in figure on either side of a 10 mm gusset plate and the member is subjected to a factored pull of 450 kN. Take size of weld as 6 mm and connections are made in workshop. [Use Fe410 grade of steel] 75 m L. C. = 31mm 16A (100 x 75 x 8) mm Choose the nearest correct statements: L1 = 390.5 mm L1 = 195.25 mm Correct Option L2 = 87.75 mm Correct Option L2 = 175.5 mm
1. The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle section with the thickness shown in the figure. The working stresses are 155 MPa for tensile member and 145 MPa for compressive member, 50 MPa for shear in the rivets and 130 MPa for bearing stress due to the rivets. How many 20 mm diameter rivets are required to fasten member DE to the gusset plate? 12 kips 8ft 12 kips 10 kips 8ft 10 kips 6ft B 4ft E F 4 ft 4 ft 22 ft 8 ft
The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle section with the thickness shown in the figure. The working stresses are 155 MPa for tensile member and 145 MPa for compressive member, 50 MPa for shear in the rivets and 130 MPa for bearing stress due to the rivets. How many 20 mm diameter rivets are required to fasten member DE to the gusset plate?
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine:a. The shear stress in the bolts.b. The axial stress in the bolts.c. The support stress in the W12X65 profile.
[Item-2] Instruction: (refer to the photo below) Kindly answer the question given and provide correct and complete solution. I will dislike your solution if it is incomplete and wrong answer. Please handwrite your solution.
2- A 2m COPPER BAR SUBJECTEO TO A TENSILE IS SUSPENDED FROM A LOAD IBO KN SUPPORTED BY TWO IDENTICAL PIN THAT S pOSIS AS SHON OF THE LOWER AFPLIED TENSILE POSTS SUPPORT THE STEEL DETERMINE THE TOTAL DEFORMATION END OF THE LOAD HINT: NOTE THAT THE STEEL PIN WHERE THE COFPER BAR IS ATTACHED. COPPER BAR DUE TO STEEL POST L=0.5m A= 4500mm E- 200GPA COPFER BAR L- am A= 4800 Mn E- l20 GPa 180KN
Is truss stable
Determine the internal force in members AF, FG,BF & CH of the truss ? using the cutting RK methodology 3m 12 KN 3m 10 kN G 3m 12 kN H ID 3m
Six rivets are used in the connection shown in the figure. If both P=50KN, what is the minimum diameter rivet is necessary so as not exceed the 70MPa allow shearing stress? What thickness of plate is required so as not exceed a bearing stress of 140MPA? p= 50 80 mm 80 mm 100 mm
snip
Please help me with my homework and use ASEP Steel Handbook 2004 volume 1 Dimensions and Properties Third Edition, to find the AISC.
"Prob. 2.9-8. The steel eyebar in Fig. P2.9-8 has cross-sec- tional dimensions 25 mm x 100 mm. To obtain the required length of bar, it is necessary to weld together two separate lengths along a diagonal joint that makes an angle with respect to the cross section. The stresses in the weld are limited to 125 MPa in tension and 75 MPa in shear. (a) Determine the optimum angle (0 ≤ 0≤45°) for the welded joint. (b) Determine the maximum safe load for the optimally spliced bar. € G