Considering the dc operating conditions of theNMOS circuit in the figure, gm = 1.9 mS wasobtained. Also, the load current I flowing throughRL when Rsigl= 2 kohm, Rsig2= 3 kohm, RF = 60Kohm, R1 = 50 Mohm, R2 = 12 Mohm, RD= 4.7 k, RS%3|= 1.2 Kohm and RL = 11.3 k What would be thevalue of ? (Vil= 20 mV, Vi2 = 30 mV) NOTE-1:Capacitors are negligible at mid-band frequency.NOTE-2: NMOS output impedance will beconsidered. and its value is rd = 20 k VccR1RDRFC2VoM1Rsig1C1VI1-NMOSRLRsig2Ideal opampV12-R2RSCS

Answered: Image /qna-images/answer/c41b4140-1072-4571-a980-2d7855cebbe1.jpg

Considering the dc operating conditions of the NMOS circuit in the figure, gm = 1.9 mS was obtained. Also, the load current I flowing through RL when Rsigl= 2 kohm, Rsig2= 3 kohm, RF = 60 Kohm, R1 = 50 Mohm, R2 = 12 Mohm, RD= 4.7 k, RS = 1.2 Kohm and RL = 11.3 k What would be the value of ? (Vil = 20 mV, Vi2 = 30 mV) NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: NMOS output impedance will be considered. and its value is rd = 20 k

Considering the dc operating conditions of the NMOS circuit in the figure, gm = 1.9 mS was obtained. Also, the load current I flowing through RL when Rsigl= 2 kohm, Rsig2= 3 kohm, RF = 60 Kohm, R1 = 50 Mohm, R2 = 12 Mohm, RD= 4.7 k, RS = 1.2 Kohm and RL = 11.3 k What would be the value of ? (Vil = 20 mV, Vi2 = 30 mV) NOTE-1: Capacitors are negligible at mid-band frequency. NOTE-2: NMOS output impedance will be considered. and its value is rd = 20 k

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

INCLUDE ALL THE DECIMALS
In this voltage divider bias circuit, the input is at the base. Output is at the emitter with a high input resistance and low output resistance. The maximum voltage gain is 1 and the coupling capacitors must have a negligible reactance at the frequency of operation. (use to answer a and b) a. Derive the expression for the voltage gain, current gain, and power gain in terms of power delivered to the load, R. b. Sketch both the DC and AC equivalent circuits. c. Derive the expression for ripple factor of Half Wave Rectification with a capacitor filter.
W Q.2) A Full-wave bridge rectifier with a (400 Sin(100)t) sinusoidal input has a load resistor of (10KS) .Sketch Vo and determine the : 1- Fi and Fo So 2- Vdc 2%. 〃 3- Vrms 4- Irms 5- Prms 6- Pdc PHO 7- Efficiency 8- Ripple Factor 9- PIV (.
2 V 1ΚΩ VOUT Find the following: a. Vout b. Small signal model of the diode under these conditions (Do NOT consider capacitance across the diode junction and the resistance of the semiconductor material outside the diode junction) c. Approx. peak-to-peak value of the AC component of Vout if a 1 mV RMS sinusoidal signal is added to the 2 V DC source. Given that: reverse saturation current is 1.5 x 10-14 A, ideality factor is 1.1, and the circuit is operating at 27°C.
9
For the given Full-Wave Bridge Rectifier circuit below with capacitor filter, it produces a ripple voltage waveform shown. If V2 is given as 12 volts and V1 is given as 6 volts, compute for the ripple peak-to-peak voltage, de voltage and ripple factor. If the load resistance has a value of 7 kiloohms, how much should be the dc current?. compute for the peak output voltage at the output of the rectifier. If silicon diodes are used, what is the value of the secondary peak voltage?. If N1 is given as 1400 and N2 is given as 500, compute for the primary peak voltage. A01 D2 A D3 D4
Q3. Multiple Choice question based of Field Effect Transistor a. The Drain current for JFET with a Pinch off voltage Vp-3volts and Drain Source Saturation Current Idss-6mA is given a bias of VGS=+1 volt is- a) 1.07mA b) 10.7mA
In the following circuit, the nMOS has a threshold voltage of Vr = 1.0 Vand K = 2 mA/VÅlso given that R1 = 3 kNVpp identical with vp. = 0.9(i.e. use CVD model for the diodes). Our task is to set the value of Rp such that the MOSFET will be operating at the edge of saturation. What's edge of saturation? We know in the triode region vps vGs – VrHence, the edge of saturation means when vps = vGS - VAt this mode, both the equations for In in saturation mode and triode mode would give the exact 6 Vand the diodes are same result, VDD VDD Rp R1 KIKKH
Explain this circuits in detail NOT and XOR gate
Design a Zener diode voltage regulator with a suitable circuit diagram and to consider the voltage regulator is used to power a cell phone at 4.5 V from a lithium ion battery pack, which voltage may vary between 5 V and 7.8 V. The current in the phone will vary 10 mA (when standby mode) to 150 mA (when talking). Assume that the Zener diode current, Iz(min) is 10% of Iz(max).
Q.7 Light-emitting diode (LED) is simply a diode that is designed to emit light. Voltage drop for LED is 0.8V. What happens to the LED when it is connected to the voltage source as in Figure A1? Why? (Describe in terms of majority carrier movement). LED 5V 1kQ Figure Al
........ (Figure-1) R. RB= 380kN,Rc= 1kN B = 100, VBB = Vcc=12V RB ww Vec CC ......... I, V CE СЕ V ВЕ BB Q-1-b) Describe briefly the input / output characteristics and application of Common Emitter BJT Configuration