Consider the system in (Figure 1) under load applied at the pads.1 ft1 ftdBD1 ftk= 150 lb/ft1 ftPart AIf d = 0.80 ft and the spring has an unstretched length of 0.900 ft, determine the force F required for equilibrium.Express your answer in pounds to three significant figures.▸ View Available Hint(s)F =SubmitProvide Feedbacklb

Given, d=0.8 ft lo= 0.9 ft Required: Force F required for equilibrium.

Consider the system in (Figure 1) under load applied at the pads. Part A If d = 0.80 ft and the spring has an unstretched length of 0.900 ft, determine the force. required for equilibrium. Express your answer in pounds to three significant figures. ▸ View Available Hint(s)

Consider the system in (Figure 1) under load applied at the pads. Part A If d = 0.80 ft and the spring has an unstretched length of 0.900 ft, determine the force. required for equilibrium. Express your answer in pounds to three significant figures. ▸ View Available Hint(s)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Problem 5.28 The disk has a mass of 12 kg. It is suspended from a spring having an unstretched length of 400 mm. (Figure 1) Figure -8- k = 600 N/m 200 mm 1 of 1 Part A Determine the angle for equilibrium. Express your answer in degrees to three significant figures. 0 = Submit OF V—| ΑΣΦ Provide Feedback Request Answer vec ?
An ideal spring, with a pointer attached to its end, hangs next to a scale. With a 100 N weight attached, the pointer indicates "40" on the scale as shown. Using a 200N weight instead results in "60" on the scale. Using an unknown weight X results in "30" on the scale. The weight X is: Hint: Draw the force - Displacement diagram. 100 N O 1.20 N O 2.30 N O 3.40 N O 4.50 N O 5.70 N
I Review Learning Goal: Part A - Finding the Cartesian components of a force described by direction angles To use the dot product to find the components of forces acting in arbitrary directions. 35.0 N, α- Find the Cartesian components of force P acting in the x, y, and z directions given P B = 41.0°, and y= 76.9°. Recall that a is the angle between the vector and the x axis, B is the angle between the vector and the y axis, and y is the angle between the vector and the z axis. 128.0°, A three-legged structure is shown below. It is attached to the ground at points B = (4.05 , 0, 0) and C = (-4.05 , 0, 0) and connected to the ceiling at point A = (-4.67 , 4.21 , 5.85). The three legs connect at point D = (0, 3.60, 3.50), where two forces, F and P, act. Force F is given by F = 3.40 i – 14.5 j+ 24.0 k N; P has magnitude 35.0 N and direction angles a = 128.0°, ß= 41.0°, and y= 76.9° for the x, y, and z axes, respectively.(Figure 1) Express your answers, separated by commas, to three…
Classify each of the structures shown as statically determinate, statically indeterminate, stable or unstable. If statically indeterminate externally, then determine the degree of statical indeterminacy. Show complete computations.
In the following figure the lamp has weight, in magnitude, of W, the spring constant is k for the spring AB, the equilibrium length of the spring is lo, the horizontal distance between C and B is d and the angle measured clockwise from the negative x-axis to AC is 0. With the provided values to follow, determine the required length of cable AC so that the system is in static equilibrium. All angles are measured in degrees, all distances are measured in m and all spring constants are measured in Nm¹. Provide your answers accurate to three significant figures. Given -50. w-200, 200, d-2 and 0.5 (all forces measured in N), provide the required values (where is the magnitude of the tension in the rope): T = AC =
The figure on the left, below, shows a non-uniform bent rod with a mass of 5 kg. Your job is to determine the location of the center of gravity of this rod. You design an experiment: you connect a pin and cable to the rod such that it safely stays in static equilibrium under a force P that you apply. Then, you apply forces between 0-100 N, and measure the tension force on the cable using a cable tension meter. The results of your experiment are shown in the figure, on the right. Using this experiment, calculate (approximately) the horizontal distance (x in the figure) between point A and the center of gravity G of the bent rod. B C O I 20 cm 20 cm 60° D 50 cm Tension measurement [N] 60 50 40 30 20 -10 0 10 real data estimated fit 20 30 40 ܐܐܝ 50 P[N] 60 70 80 90 100
uld be saved and this message will disappear. U d. Mo = 2007 + 400K The unstretched length of spring AB is 1 m. If the block is held in the equilibrium posítion shown, what would be the weight of the block at D? Hint: Find the stretched length of spring AB and use the equilibrium. 3 m m B 3 m kAC=20 N/m kAB 30 N/m wwww Select one: O a. none of these
STATIC I need the answer within 1 hour. Thanks Using the knot method, find the force that each element in the truss system carries. Indicate whether these elements are under tensile force or under compression force. F1(N)=11 , F2(N)=23
Problem 2: 2D Equilibrium (30 % ) A weight of 100 lb is supported by two ropes as shown. Calculate the tension in each rope needed to keep the weight in this equilibrium position. 50° 750 FBD TCA = TCB = If the breaking tension of each rope cord is 120 lb, will the cords support the system as shown? Explain why or why not. Explain O Yes they will hold O No, something will break
Question 3: The free body diagram of the back model in static equilibrium is shown in Figure 1 below. Develop an equation for T as a function of W in terms of the defined variables. Hint: take a moment about the lower back where Fx and Fy act (i.e. lower lumbar spine). Please show your work! Fx LT LEDER F₁ W₂ Lb W un mun -Lw b Figure 1. Free body diagram of the back model. T is the tension exerted by the extensor muscles (all muscles combined), Wo is the weight of the upper body (torso and arms), W is the weight of the object held in the hand. LT is the perpendicular moment arm of T; Lo and Lw are the perpendicular moment arms of W, and W. A
Please show the solution and free body diagram of the image below. Thanks! Subject: Statics of Rigid Bodies Topic: Equilibrium in Two Dimensions
Torque Problem The diagram below shows the lower leg being held in a stationary. The torque acting to turn the leg in a clockwise direction is being generated by the weight of the leg and the weight of a barbel attached to the ankle. Using the information provided calculate the magnitude of the quadriceps force. LOWER LEG IN ANGULAR EQUILIBRIUM 15° Quadriceps muscle force 0.05m 0.14 m 50° 0.30m 90 Newtons 120 Newtons Show your calculations step by step here. Includes diagrams and short comments to explain your approach to solving the problem.