In (Figure 1), the forces in members A and Care FA 4 kN and Fc = 3 kN. The force system is concurrent at point O. Determine the forces acting on members B and D that are required for equilibrium. Figure 60 <1 of 1 > ▼ ▼ Part A Determine FB- Express your answer to three significant figures and include the appropriate units. Submit FB-2.463 kn The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Part B μA Previous Answers Request Answer Submit Determine Fp. Express your answer to three significant figures and include the appropriate units. ? HA FD= 4.898 kn The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Previous Answers Request Answer ?

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: Q3: Mark the Following True or False 1. Hidden lines are used in sectioned area when they are needed…

A: 1.TRUE 2. TRUE 3.TRUE 4.FALSE 5. FALSE 6.FALSE 7.TRUE 8.FALSE 9.FALSE 10.FALSE 11.TRUE 12.TRUE…

Q: A part may be properly represented on an engineering drawing with as few views as: A. one B. two…

A: Please find the answer in the next page.

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: Write TRUE is the statement/s is True. If the statement is false, identify the word/s that makes the…

A: The chip compression ratio can be defined as the ratio of the chip thickness and uncut chip…

Q: What's the answer C onwards with working and correct answer and can you label it please as I have…

A: The ideal diesel cycle does not occur in practical life because the losses are not eliminated in…

Q: What is Line J? ARROWHEAD .35mm A 7.0 В

A: Solution:

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: C) What is the maximum possible mass flow rate that the pump can produce?

A:

Q: How many cutting-plane lines are shown on this print?

A: Cutting plane lines:Cutting plane lines are the lines used to show the direction of the cut-way…

Q: Consider the crank assembly of the figure. The bearings at points A and B are in good alignm…

A:

Q: I need problems 7, 8, and 9 answered pertaining to the print attached below.

A: Cutting plane line:Cutting plane lines are represented by dotted chain line as shown in the figure.…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: Beam deflection is to the length to a beam. OA. flexure

A: Explanation As we know that the deflection of any beam always follow the equation of elastic curve…

Chemical and Phase Equilibrium

Phase diagrams or equilibrium phase diagrams are the graphical representations that show the phase transformations of the constituting elements with respect to the pressure, temperature, and compositions. The diagrams show the conditions that limit the different phases, namely solid, liquid, and gas. The diagram can also be utilized to verify the relations between the state variables. Most of the phase diagrams are temperature-pressure phase diagrams, with the variable parameter as the composition. Usually other variables such as solubility and pressure parameters are not indicated in the phase diagram. For a one-component system (unary phase diagram), the phase diagram is generally a function of temperature and pressure as the state variables, or temperature and volume. However, for a binary system (two-phase) having two components, the phase diagram is a function of temperature and composition as the state variables only. Coexisting of the different phases of the constituting elements is indicated in the phase diagram. A ternary phase diagram can be characterized by consisting of three phases in equilibrium.