Consider the magnetic circuit in figure.current of (3A) flowsthrough 200 turns of wire around a core of cross sectional aea of0.24 (m)103 m? and a relative permeability of 5000.2 (mm)a) Determine the magnetic flux in each legb) Determine the magnetic field intensity in the air gap-0.2 (m)0.2 (m)c) Determine the magnetic force on the across the air gap

a) Consider the magnetic circuit with air gap is shown in Figure 1. Figure 1 Consider the…

Consider the magnetic circuit in figure. A current of (3A) flows through 200 turns of wire around a core of cross sectional aea of 103 m?and a relative permeability of 5000. 2 (mm) Determine the magnetic flux in each leg b) Determine the magnetic field intensity in the air gap -0.2 (m) 0.2 (m) -

Consider the magnetic circuit in figure. A current of (3A) flows through 200 turns of wire around a core of cross sectional aea of 103 m?and a relative permeability of 5000. 2 (mm) Determine the magnetic flux in each leg b) Determine the magnetic field intensity in the air gap -0.2 (m) 0.2 (m) -

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the magnetic circuit shown in the figure, the iron core with N = 500 turns -Magnetic permeability is 200. its average length is 40 cm -The diameter of the cross-sectional area is 1 cm. Find the current that must pass through the winding to produce 0.5 mWb of flux in a 1mm air-gap magnetic circuit?
3 Biot-Savart for Curved Wire A segment of a closed current loop is shown in the following figure. Compute the magnetic field at the center of the semi-circle due to the straight and curved segments shown. b (Technically, to use the Biot-Savart law for currents in a wire, the current must be constant, and the wire must form a closed loop. As a result, there will be a contribution to the magnetic field at the origin due to the parts of the closed loop that are not shown. However, here we assume that the not- shown part of the loop is far enough away that they can be neglected.)
A magnetic ring has reluctance of 1.675 × 10⁰ AT weber. The flux to be produced by the coil is 800 x 10 webers, then the AT required for the m.m.f. will be
how does the electrostatic discharge occur in the following situation? explain with suitable mathematical substantiation a. Insulator surface are rubbing together. b.Insulator surface are pulling apart.
A flux of 0.0016 Wb flows in a silicon sheet steel coil/core. The arrangement appears as shown below with the following dimensions: Ac = 0.0025 m? Core/gap area: Flux path length: le = 0.350 m lg = 0.0015 m N = 500 Air gap length: Number of turns: %3D A. What is the current, I, through the winding? B. What is the energy stored in the inductance? C. Assume that the current is given by i =9.75 sin (3147) A. What is the RMS voltage that would appear across the winding? D. Assume that the gap is removed from the arrangement with the flux path remaining at 0.350 m. For a flux of 0.0016 Wb, what is the inductance of the arrangement? E. What is the energy stored in the inductance with the gap removed?
An iron circuit with a small0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm2, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (u, = 800 for iron). Figure 1
Figure Q1(a) shows a piece of ferromagnetic core with magnetic flux (B) with circular current (I) around the core. Figure Q1(b) show laminated ferromagnetic core with the same magnetic flux (B) and circular currents. With the aid of diagrams, explain how the current as highlighted in red (I) is developed in the ferromagnetic core in Figure Q1(a). B (a) (b) Figure 1(a) A ferromagnetic core and (b) laminated ferromagnetic core
An iron circuit with a small 0.75 mm air gap is shown in Figure 1. A 6000 turn coil carries a current I = 18 mA which sets up a flux within the iron and across the air gap. The cross section of the iron is a consistent 0.8 cm?, and the mean length of the flux path is 0.15 m. a) Redraw the magnetic circuit using schematic symbols of an electric circuit with reluctance in each part of the circuit. b) State's Ohm's Law for magnetic circuit. c) By neglecting the effect of fringing, calculate the reluctance of the circuit. d) Find the flux within the core. N = 6000 Iron circuit (4, = 800 for iron). Figure 1
6) a) Current is generally defined with respect to ...b) Current in a wire is defined with respect to ...c) Derive how much current flows through a closed surface in the magnetostatic case. d) Derive magnetic flux through a closed surface for a non-magnetostatic case.
To a magnetic core, with a relative permeability of 2100, a current I1 of 1 A and a current I2 of 2 A are applied, where the number of turns of the winding is 1000. The depth of the magnetic core is 20 cm. take into account that the bounded measurements are given in centimeters. The air gap shown in the figure is 0.2 cm and has an effective area equivalent to 1.1 times the cross-sectional area of the core. Determine:a) The equivalent circuit with sources and reluctance (Graph it)b) The magnetic flux of the central columnc) Magnetic induction at point Ad) Explain what would happen if the flow of current I1 is reversed
Q4// A ring of a mean diameter 30 cm and cross sectional area of 15 cm2 is made up of semi – circular sections of cast iron and cast steel. If each joint has an air gap of 0.25 mm. Find amper turns required to produce a flux of 7 x 10 weber in the magnetic circuit. The relative permeability of steel and iron are 852 and 165 respectively. - OA- Amper turns required= 1105 OB- Amper turns required= 1995 OC- Amper turns required= 2250 OD- Amper turns required= 3150 OE- None of above ارسال الاجابة
In figure, a magnetic flux of F is generated with a constant current of i. The core material used has a relative permeability of 4000. Assuming that the mean cross sectional area that the magnetic flux passing through in core is A=4 [cm2] and there is no fringing in air gap, N= 1000 turns and i=10 [A], lair=2 [mm]. what is the reluctance in air gap? what is the total reluctance? what are the flux and flux density in air gap? Remember: µ0 = 4πx10-7 Answers:Rair = ___________ [At/Wb]Rtotal = _________ [At/Wb]φ = ___________ [Wb]B = ________[T]