Consider the circuit shown in figure, where Ve=710 mV, B = 100, and VA = ∞o. Assume that the emitter current is equal to collector current. Şekildeki devre için VBE-710 mV, B = 100 ve VA = ∞ olduğunu dikkate alınız. Emiter akımının kollektör akımına eşit olduğunu kabul ediniz. Circuit parameters/Devre Parametreleri RB = 150 kn, Rc = 0,9 k2, R = 0,4 k2, Vcc=7V -> Alttaki devre için Q₁ transistörünün kollektör akımını Iç belirleyiniz. (Determine the collector current Ic of Q₁ for the circuit shown below.) (doğru katsayısı: 0.5) -> Alttaki devre için Q₁ transistörünün kollektör-emiter gerilimini VC belirleyiniz. (Determine the collector-emitter voltage VCE of Q₁ for the circuit shown below.) (doğru katsayısı: 0.5) Not: Üstteki iki sorunun her biri için bir tane olmak üzere cevaplar arasından toplamda sadece iki tane seçim yapınız. Çözüm sonunda bulamadığınız bir cevap için rastgele işaretleme yapmayınız. Her doğru cevap soru puanının yarısı kadar puan eklemekte, her yanlış cevap ise soru puanının 8'de biri kadar puan eksiltmektedir. Vcc Rc RB W-" RE

Q: What is the total current for the circuit in the figure below? Given: R = 3000 Xc= 150 120 v 60 Hz…

A: The circuit diagram,The resistance, The capacitive reactance,

Q: I need the expert solution handwritten in full for the question, not an explanation.

A: Step 1:Step 2:

Q: Part 1. Thermistor sensitivity in a voltage divider Thermistors are temperature-sensitive resistors.…

A:

Q: Need help steps would be helpful please and thank you! R1 = 1000 R2= 2000 C=6uF L=1mH

A:

Q: Subject to a step input, the voltage drop across the resistor took 696.3103us to reach 13% of its…

A: for study state , L gets short so  ,i = ViR  ,  V0=Vi As voltage drop across L is 0 at study…

Q: R1 R2 C2 S +

A:

Q: can you please explain how we do the d) section

A:

Q: The South American eel can generate electric current that can stun and even kill nearby fish. The…

A: Given Data:An equivalent circuit of an eel with,The number of series connections The number of…

Q: Answer the questions and submit the photos for questions 2 - 9using the circuit from STEP 2. R1 50 Q…

A:

Q: For the following transfer/system functions s²-28+2 (a) H(s) = (4s+3)(6s²-s-1) (b) H(s) = 3s²+48-4…

A: The given transfer / system functions area. H(s)=s2−2s+2(4s+3)(6s2−s−1).b.…

Q: admittance Hybird paramter(h).

A: The solution can be achieved as follows.

Q: Initially a 10 V battery is in series with a 100 ohm resistor and a 2 mH inductor. After a long…

A: Inductor doesn't allow sudden change of current.

Q: b) b 4 Short admittance

A:

Q: Consider the following RL circuit with Vs-200V, R1-100 ohm, R2- 100 ohm, R3- 50 ohm, L-20 H. The…

A: The general expression of inductor current in series RL Circuit Charging…

Power Amplifier

The power amplifier is an electronic amplifier designed to maximize the signal strength of a given input. The input signal strength is enhanced to a high enough level to drive output devices such as speakers, headphones, RF (Radio frequency) transmitters, etc. Unlike voltage / current amplifiers, the power amplifier is designed to drive core loads directly and is used as a storage block in the amplifier series.

Maximum Efficiency Criterion

In every field of engineering, there is a tremendous use of the machine and all those machines are equipped for their popular work efficiency so it very much important for operation engineers to monitor the efficiency of the machine, planning engineers to check out the efficiency of the machine before installing the machine and design engineers to design machine for higher efficiency than and then the utility will procure their products that will ultimately lead to profit and loss of the company. It indicates the importance of efficiency right from the initial stage as manufacturing units, intermediate stage as planning coordinators, and end-users stage as a utility.