Consider the bistable circuit of the circuit above right with the negative input terminal of the op-ampdisconnected from the ground and connected to a reference voltage VR.Derive expressions for the threshold voltages V and VrH in terms of the op-amp saturation levels L,and L-, as well as R1, R2, and VR. Let L+ = - L- = Vi, and R1 = 20 kN. Find R2 and Vr that result in thresholdvoltages of 0 and Vi / 5. Sketch the v, – Vo characteristics of the bistable circuit for VR = 10 V and V, = 15 V.RR2

Answered: Image /qna-images/answer/4e78a8e6-2576-449e-b1da-73dba299ce84.jpg

Consider the bistable circuit of the circuit above right with the negative input terminal of the op-amp disconnected from the ground and connected to a reference voltage VR. Derive expressions for the threshold voltages VTL and VTH in terms of the op-amp saturation levels L, and L., as well as R1, R2, and VR. Let L. = - L-= V., and R1 = 20 k2. Find R2 and VR that result in threshold voltages of 0 and V. / 5. Sketch the v, – Vo characteristics of the bistable circuit for Vr = 10 V and V, = 15 V. R1 R2

Consider the bistable circuit of the circuit above right with the negative input terminal of the op-amp disconnected from the ground and connected to a reference voltage VR. Derive expressions for the threshold voltages VTL and VTH in terms of the op-amp saturation levels L, and L., as well as R1, R2, and VR. Let L. = - L-= V., and R1 = 20 k2. Find R2 and VR that result in threshold voltages of 0 and V. / 5. Sketch the v, – Vo characteristics of the bistable circuit for Vr = 10 V and V, = 15 V. R1 R2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

6. For common-source small-signal FETS, the output voltage is 180° phase shifted with respect to the Q 7. The operating cycle of a Class A amplifier is Q 8. The maximum efficiency of a Class B amplifier is Q 9. In analyzing op-amps, when the non-inverting input pin is at ground and the inverting input pin is also at 0 V for an AC signal, the technique is called as Q 10. is an op-amp application circuit which is useful in low pass filter circuits.
The ideal op-amps depicted can swing rail-to-rail at output, and Vcc= 13 V. Initially, the output voltage Vo = +13 V and the input voltage is vS = -13 V. The feedback resistors are R1 = 6.4 k0, R2 = 8.5 kQ, and R3 = 1.6 KQ. If the input voltage is gradually increased, at what value of vS (to 1% accuracy) does the output voltage (Vo) change to Vo=-Vcc? VVV vS = + R10 Vcc -Vcc R20 04 O Vo
TRUE OR FALSE1. Due to the infinite open-loop volatge gain of an ideal op-amp, its diferrential input voltage should approach zero for the output voltage to be finite.2. An op-amp is a voltage amplifier circuit with very high gain, very high input resistance, and a very high output resistance.3. The input resistance of an ideal op-amp is infinite resulting to the simplifying condition that the voltage at the non-inverting input is essentially equal to the voltage at the inverting input.4. For an op-amp differentiator circuit, if the input voltage is a sine wave then the output is also a sine wave that is in-phase with the input.5. The gain of a non-inverting amplifier can be adjusted to values less than 1 or greater than 1 by using appropriate values of the external resistors.
5 please all parts will give like!!!
Q.3 (a) Figure Q. 3(a) shows a basic op amp circuit. (i) State current and voltage assumptions that are used to analyse the op amp circuit. (ii) Explain the function of +Vcc and -Vcc in the linear op amp operation. (iii) Give one advantage of using op amp compared to a single BJT transistor in amplifier circuit. +Vc V+ I- Vo V- - Vec Figure Q. 3(a) SITI NOLOC
3G Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. Determine the output voltage of the second stage stage. a.-2640 mV b.-26.4 mV c.-1.2 mV d.26 V
Choose the correct answer. *Please answer it ASAP if you can*
Need help with this problem down below.
3A Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. 3H Determine the total gain of the circuit in Problem No. 1 (P1) a.792.105 b.9000 c.792 V d.792
Need help with this Q2a
A certain op-amp has three internal amplifier stages with midrange gains of 30 dB, 40 dB, and 20 dB. Each stage also has a critical frequency associated with it as follows: fc1 = 600 Hz, fc2 = 50 kHz, and fc3 = 200 kHz. (a) What is the midrange open-loop gain of the op-amp, expressed in dB? (b) What is the total phase shift through the amplifier, including inversion, when the signal frequency is 10 kHz?
2. Suppose we have an op-amp that is powered by a ±15 V supply (assume Vout max is ±14V), and has a maximum output current of 50 mA. The maximum slew rate of the op amp is 107 V/s. In the circuit below where Vin=5sin(100t). a. What would the output voltage Vout be if the op amp were ideal? b. Compute and draw the actual output voltage if a load resistor of Rload=100 N is attached to Vout. Vin ww 1 ΚΩ ww 4 ΚΩ + +15V Op-Amp -15V Vout