a.derive the expression for the close- loop gain for an op amp non inverting amplifier b.the input of an op amp differentiator is a sinosiodial voltage peak of value 150uV voltage of frequency 10hz.determine the output voltage if the R=25ohms and C=2uf. C.An inverting amplifier has Rf=200ohms and R1= 12ohms. Determine the amplifier circuit voltage gain,input resistance and output resistance, determine also the output voltage, and input current if the voltage is 0.3. Assump it is an ideal op amp.

a.derive the expression for the close- loop gain for an op amp non inverting amplifier b.the input of an op amp differentiator is a sinosiodial voltage peak of value 150uV voltage of frequency 10hz.determine the output voltage if the R=25ohms and C=2uf. C.An inverting amplifier has Rf=200ohms and R1= 12ohms. Determine the amplifier circuit voltage gain,input resistance and output resistance, determine also the output voltage, and input current if the voltage is 0.3. Assump it is an ideal op amp.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q7. Find the relationship between the output and the input (Vout/Vin ) in the amplifier circuit depicted in Figure Q7 (a) and (b). State any assumptions you make. Please step by step I need to understand.
An inverting amplifier is to be designed with a gain of 5 and an input impedance of 10k ohms. What should be the value of the feedback resistance?
A. An inverting Amplifier with a real Op-Amp that has a gain time of 0.001ms and Vcc = ±20 V find the following: 1. Circuit bandwidth? 2. For Vin = 10 sin wt volt, sketch the output waveform for the gain ratio of 15 case.
6. For common-source small-signal FETS, the output voltage is 180° phase shifted with respect to the Q 7. The operating cycle of a Class A amplifier is Q 8. The maximum efficiency of a Class B amplifier is Q 9. In analyzing op-amps, when the non-inverting input pin is at ground and the inverting input pin is also at 0 V for an AC signal, the technique is called as Q 10. is an op-amp application circuit which is useful in low pass filter circuits.
Introducion to Electronic Analysis and Design - CE05 To have a good amplifier Select one: a. The input resistance should be high b. the output resistance should be high c. the voltage gain should be equal to zero d. the current gain should be equal to zero Ssment CE255/EE255 (O1)- Dr. Mamoun Al-Mistar Jump to...
Q.3 (a) Figure Q. 3(a) shows a basic op amp circuit. (i) State current and voltage assumptions that are used to analyse the op amp circuit. (ii) Explain the function of +Vcc and -Vcc in the linear op amp operation. (iii) Give one advantage of using op amp compared to a single BJT transistor in amplifier circuit. +Vc V+ I- Vo V- - Vec Figure Q. 3(a) SITI NOLOC
3G Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. Determine the output voltage of the second stage stage. a.-2640 mV b.-26.4 mV c.-1.2 mV d.26 V
Given the circuit in figure. Derive the formula of voltage gain and current gain using complete hybrid pi model. Draw the AC equivalent circuit
Choose the correct answer. *Please answer it ASAP if you can*
3A Problem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. 3H Determine the total gain of the circuit in Problem No. 1 (P1) a.792.105 b.9000 c.792 V d.792
Table Q2 shows the datasheet comprising the parameters of a practicalop-amp. Please answer the following questions with reference to the data inTable Q2. Determine the full-power bandwidth for a 10-V output. Using the typical values from Table Q2, find the magnitude of thecommon-mode gain, Acm.
Draw a circuit diagram of a Class-C power amplifier. Explain the reason why a Class-C power amplifier is in general more efficient than a Class-B power amplifier. What is the main disadvantage of Class-C power amplifiers?