Consider the beam shown in (Figure 1). Take P = 33 kN. Part A Determine the normal stress at point A on the cross section of the beam at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. for Part A for Party do for Part redo for Part A reel for Part A keyboard shortcuts for Part A help for Part A Value Submit Request Answer Part B Units Determine the shear stress at point A on the cross section of the beam at section a-a. Express your answer to three significant figures and include the appropriate units. for Rart B for Partido for Part redo forart B resor Part B keyboard shortcuts for Part B help for Part B Value Units Submit Request Answer Figure 0.5m 0.51 -100 mm 50 mm 2m 10mm 180 mm 10 mm Section a-a 10mm <1 of 1 >

Consider the beam shown in (Figure 1). Take P = 33 kN. Part A Determine the normal stress at point A on the cross section of the beam at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. for Part A for Party do for Part redo for Part A reel for Part A keyboard shortcuts for Part A help for Part A Value Submit Request Answer Part B Units Determine the shear stress at point A on the cross section of the beam at section a-a. Express your answer to three significant figures and include the appropriate units. for Rart B for Partido for Part redo forart B resor Part B keyboard shortcuts for Part B help for Part B Value Units Submit Request Answer Figure 0.5m 0.51 -100 mm 50 mm 2m 10mm 180 mm 10 mm Section a-a 10mm <1 of 1 >

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter12: Static Equilibrium And Elasticity

Section: Chapter Questions

Problem 64P: When using a pencil eraser, you exert a vertical force of 6.00N at a distance of 2.00cm from the...

See similar textbooks

Similar questions

The uniform boom shown below weighs 3000N . It is supported by the horizontal guy wire and by the hinged support at point A. What are the forces on the boom due to the wire and due to the support at A? Does the force at A act along the boom?
A uniform rope of cross-sectional area 0.50cm2 breaks when the tensile stress in it reaches 6.00106N/m2 . (a) What is the maximum load that can be lifted slowly at a constant speed by the rope? (b)What is the maximum load that can be lifted by the rope with an acceleration of 4.00m/s2 ?
Use the graph in Figure P14.46 to list the three materials from greatest Youngs modulus to smallest. Explain your reasoning. FIGURE P14.46
Review. A student is supplied with a stack of copy paper, ruler, compass, scissors, and a sensitive balance. He cuts out various shapes in various sizes, calculates their areas, measures their masses, and prepares the graph of Figure PI.51. (a) Consider the fourth experimental point from the top. How far is it from the best-lit straight line? Express your answer as a difference in vertical-axis coordinate, (b) Express your answer as a percentage, (c) Calculate the slope of the line, (d) State what the graph demonstrates, referring to the shape of the graph and the results of parts (b) and (c). (e) Describe whether this result should be expected theoretically, (f) Describe the physical meaning of the slope.
(a) When water freezes, its volume increases by 9.05% (that is, V/V0=9.05102 ). What force per unit area is water capable of exerting on a container when it freezes? (It is acceptable to use the bulk modulus of water in this problem.) (b) Is it surprising that such forces can fracture engine blocks, boulders, and the like?
In order to get his car out of the mud, a man ties one end of a rope to the front bumper and the other end to a tee 15 m away as shown below. He then pulls on the center of the rope with a force of 400 N, which causes its center to be displaced 0.30 m, as shown. What is the force of the rope on the car?
Two muscles in the back of the leg pull upward on the Achilles tendon, as shown below. (These muscles are called the mediaI and lateral heads of the gastrocnemius muscle.) Find the magnitude and direction of the total force on the Achilles tendon. What type of movement could be caused by this force?
Consider again the two wind turbines in Problem 32. a. At what point along the 40-m blade would the angular speed of thepoint be the same as the angular speed at the end of the 20-mblade? Explain your answer. b. At what point along the 40-mblade would the translational speed of the point be the same asthe speed at the end of the 20-m blade? Explain your answer.
Hanging from the ceiling over a baby bed, well out of baby’s reach, is a string with plastic shapes, as shown here. The string is taut (there is no slack), as shown by the straight segments. Each plastic shape has the same mass m , and they are equally spaced by a distance d , as shown. The angles labeled describe the angle formed by the end of the string and the ceiling at each end. The center length of sting is horizontal. The remaining two segments each form an angle with the horizontal, labeled . Let T1 be the tension in the leftmost section of the string, T2 , be the tension in the section adjacent to it, and T3 be the tension in the horizontal segment. (a) Find an equation for the tension in each section of the string in terms of the variables m,g , and . (b) Find the angle in terms of the angle . (c) If =5.10 , what is the value of ?(d) Find the distance x between the endpoints in terms of d and .
A company is testing a new material made of recycled plastic for use in construction. Figure P14.48 is a graph of the stress as a function of strain for this material. Find Youngs modulus for this material and compare your result with the data for conventional building materials listed in Table 14.1.
Consider the situation in Problem 25. Tests have shown that when people try to eyeball the proper angle for the ladder, theyare often off by as much as 9. Suppose the painter sets up theladder at too small an angle. a. At what maximum angle would rubber ladder tips on dryconcrete be unsafe? b. How likely is it for a person to make such a dangerousmistake?
Two thin rods, one made of steel and the other of aluminium, are joined end to end. Each rod is 2.0m long and has cross-sectional area 9.1mm2 . If a 10,000N tensile force is applied at each end of the combination, find: (a) stress in each rod; (b) strain in each rod; and, (c) elongation of each rod.