Use for the ice? List allsumptions.1.4Consider axial flow of water in a cold tube. Write the heat conductionequation for the ice forming axisymmetrically on the inside surfaceof the tube.icewater1.5Consider two-dimensional conductionin the semi-circular cylinder shown.The cylinder is heated with uniformpe here to search05:48A qu) * ENG r-ny-E/-Fhp

Answered: Image /qna-images/answer/f62d7a60-7133-4779-8a88-e8c616ac82d1.jpg

Answered: Consider axial flow of water in a cold…

Consider axial flow of water in a cold tube. Write the heat conduction equation for the ice forming axisymmetrically on the inside surface of the tube. ice water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hot water at 160 ⁰C is passing through a pipe, and it is lagged with a plastic covering. The coefficient of thermal conduction of the plastic is 0.2 Wm-1K-1 and the heat transfer coefficient is 16 Wm-2K-1. The ambient temperature surrounding the pipe is 25 ⁰C. Determine the critical radius and hence the maximum heat loss. Calculate the heat loss for varying thicknesses of lagging and plot this against the thickness. From the graph, estimate an optimal thickness of lagging and explain your reasons. You can use Excel for the calculations and plotting.
Hello Sir,Good Evening. I have a question in my homework related Heat Transfer lesson. The following below is my question. Please Advice. Thank You "Briefly describe the steps we need to take to calculate the rate of heat transfer (heat flux) for flow through a cylinder with a circular cross section for a Reynolds number of 10,000.Write down the equations involved."
To cool the hot oil, an engineer has suggested that the oil be pumped through a submerged pipe in a nearby lake. The pipe (external diameter = 20 cm) will be placed in the horizontal direction. The average pipe outer surface temperature is 130 °C. The temperature of the surrounding water is assumed to be constant at 10 °C. Pipe length 150 m. If it is assumed that there is no movement of water. a. Determine the convective heat transfer coefficient of the outer pipe surface to the water. =AnswerWatts/ (m² °C) b. Determine the rate of heat transfer from the pipe to the water. =AnswerkW
Consider axial flow of water in a cold tube. Write the heat conduction equation for the ice forming axisymmetrically on the inside surface of the tube.
Consider a pipe of 5 m in length and 1 cm in diameter. Temperature difference between the wall and the fluid (k = 1 W/mK) at exit is 25% that of at inlet. If the pipe wall temperature remains as constant of 80 ºC, total heat transfer rate 1000 W, and the flow is laminar what is the fluid temperature at inlet?
the question is in heat conservation
A technique for measuring convection heat transfer coefficients involves bonding one surface of a thin metallic foil to an insulating material and exposing the other surface to the fluid flow conditions of interest. L Th = Foil (Pelect T) Foam Insulation (k) -Ть By passing an electric current through the foil, heat is dissipated uniformly within the foil and the corresponding flux, Pee may be inferred from related voltage and current measurements. If the insulation thickness Land thermal conductivity k are known and the fluid, foil, and insulation temperatures (T., Ts, T₁) are measured, the convection coefficient may be determined. Consider conditions for which T = T = 25°C, P =2200 W/m², L = 10 mm, and k = 0.040 W/m.K. elec (a) With water flow over the surface, the foil temperature measurement yields T, = 27°C. Determine the convection coefficient, in W/m²K. What error, in percent of this value, would be incurred by assuming all of the dissipated power to be transferred to the water…
A square-section ventilation with a side length of 0.3 mthe outer surface of the duct is 19 ° C due to the air flow through itat temperature. If this horizontal duct is not insulated and a houseIf passing through an empty room at 35 ° CWhat will be the heat gain for 1 m length?
Heat transfer
Derive the equation that gives the heat transfer rate at steady conditions for a sphere with inside diameter r1 outside diameter r2 and r1/r2 ratio 1.5. Repeat the same process for a cylinder with inside diameter r1 outside diameter r2 and r2/r1 ratio 5 and both systems Compare the heat transfer rates you obtained for
Q. IsTeam at 605 K Flow in Alpipe with thermal conductivity K=188 W/m.c whose in and out diamter D₁ = 2 inche and D₂= 58 mm respectively. The pipe is covered with Turo insulation material First was glass wool K=0,06 and second cyas insulation K=0,01 w/m.c. Firs.T 33mm and second 13 mm, Heat is Lost to the surrounding al Too Too2 = 288K by natural convection and radiation, with combined. heat Transfer coefficent of he-22,8 W/m²c. Taking heat Transfer coefficent inside pipe To be hi-48.9 W/m² c. Find Heat loss poo length and Temp. dropp. ?? *
It is aimed to produce frozen potatoes in a newly established business. The entry temperature of the cleaned potato to the system is -16 °C, and the desired temperature to reach 10 °C. For this purpose, a refrigerant at -25 °C will be used. In the freezing process, potatoes of certain sizes are placed in the ice cream basket, the basket is immersed in the tank containing the refrigerant and kept during freezing. A cooling system is designed around the tank and 1M Joule per hour removes heat from the tank to keep the temperature of the tank constant at -25 °C. It is desirable to produce potatoes of different shapes. These shapes are spheres with a diameter of 20 mm, a cube with dimensions of 16x16x16 mm and a rectangular prism with a diameter of 12x12x25 mm. In such a process,a. What should be used as refrigerant?b. What is the daily production capacity for each product?c. What would you recommend to increase production capacity?