Consider an air standard Brayton cycle. Air enters the compressor at 100 kPa, 300 K. At the cycle, pressure ratio is 9 and rejected heat (qout) is 450 kJ/kg. Determine the work output (wnet) in kJ/kg applying the cold-air-standard assumptions. (for air c,-0.718 kJ/kg.K, Cp 1.005 kJ/kg.K, k-1.4)

Consider an air standard Brayton cycle. Air enters the compressor at 100 kPa, 300 K. At the cycle, pressure ratio is 9 and rejected heat (qout) is 450 kJ/kg. Determine the work output (wnet) in kJ/kg applying the cold-air-standard assumptions. (for air c,-0.718 kJ/kg.K, Cp 1.005 kJ/kg.K, k-1.4)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw and label the P-V and T-S diagrams. In an ideal Brayton cycle, air enters the compressor section at 14.7 psia and 55°F. The pressure ratio is 12. Turbine inlet condition of 1300°F. Determine the following:a. Work, per unit massb. Heat Rejected, per unit massc. Thermal Efficiency
An air standard Otto cycle at the start of the isentropic compression has P₁ = 100 kPa and T₁ = 27°C. The compression ratio is 10 and during the heat addition process 1000 kJ/kg are supplied. Using the cold air standard analysis method, the net work for this cycle is most nearly equal to: A. 960 kJ/kg B. 900 kJ/kg C. 602 kJ/kg D. 333 kJ/kg E. Cannot be determined with the given information
3The rate of heat addition to an ideal air-standard Brayton cycle is 1.0 x 107 Btu/h. The pressure ratio for the cycle is 12 and the minimum and maximum temperatures are 520°R and 2800°R, respectively.Determine:(a) the percent thermal efficiency of the cycle.(b) the mass flow rate of air, in lb/h.(c) the net power developed by the cycle, in hp.
THERMODYNAMICS Consider an air-standard Otto cycle with a heat addition of 800 Btu/bm of air, a compression ratio of 7, and a pressure and temperature at the start of the compression process of 13 lbf/in2, 50 F to simulate an actual spark-ignition engine. Determine the maximum pressure and temperature of the cycle, the thermal efficiency of the cycle, and the mean effective pressure assuming the variation of specific heat with the value from table A-19E Show Complete solution on a paper.
Air enters the compressor of an ideal air-standard Brayton cycle at 110 kPa, 289 K, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 12:1. The turbine inlet temperature is 1567 K. Take the gas constant as 289 J/kg.K and Specific heat at constant pressure and constant volume for air as 1.004 kJ/kg K and 0.708 kJ/kg K respectively. Calculate the net power developed to two decimal places and include the correct SI unit symbol.
An air-standard dual cycle has a compression ratio of 8.6 and displacement of Vd= 2.2 L. At the beginning of compression, p1= 95 kPa, and T1 = 290 K. The heat addition is 4.75 kJ, with one quarter added at constant volume and the rest added at constant pressure. Determine: a) each of the unknown temperatures at the various states, in K. b) the net work of the cycle, in kJ. c) the power developed at 3000 cycles per minute, in kW. d) the thermal efficiency. e) the mean effective pressure, in kPa. Step 1 X Your answer is incorrect. Determine each of the unknown temperatures at the various states, in K. T2 = i 685.79 K T3 = i 1268.14 K T4 = i 2531.97 K T5 = i 0.55 K Hint
Required information Problem 09.015 - 3-Step Air-Standard Cycle with Constant Specific Heats - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS An air-standard cycle with constant specific heats at room temperature is executed in a closed system with 0.003 kg of air and consists of the following three processes: 1-2 v= Constant heat addition from 95 kPa and 17°C to 380 kPa 2-3 Isentropic expansion to 95 kPa 3-1 P = Constant heat rejection to initial state The properties of air at room temperature are cp = 1.005 kJ/kg-K, cy= 0.718 kJ/kg-K, and k = 1.4. Problem 09.015.b - Net Work for Constant Heat Capacity Air-Standard Cycle Calculate the net work per cycle, in kJ. (You must provide an answer before moving on to the next part.) The net work per cycle is kJ.
H.W2: An air-standard Carnot cycle is executed in a closed system between the temperature limits of 350 and 1200 K. The pressures before and after the isothermal compression are 150 and 300 kPa, respectively. If the net work output per cycle is 0.5 kJ, determine (a) the maximum pressure in the cycle, (b) the heat transfer to air, and (c) the mass of air. Assume variable specific heats for air. Answers: (a) 30,013 kPa, (b) 0.706 kJ, (c) 0.00296 kg
Air enters the compressor of an ideal air-standard Brayton cycle at 100 kPa, 314 K, with a volumetric flow rate of 5 m3/s. The compressor pressure ratio is 9:1. The turbine inlet temperature is 1400 K. Take Specific heat at constant pressure and constant volume for air as 1.006 kJ/kg K and 0.717 kJ/kg K respectively. Calculate the compressor exit absolute temperature to one decimal place and place the correct unit. Use the cold air-standard assumption.
Air enters the compressor of an ideal air-standard Brayton cycle at 80 kPa, 299 K, with a volumetric flow rate of 6.1 m3/s. The compressor pressure ratio is 7. The turbine inlet temperature is 1886 K. Adopting the cold air-standard assumption, calculate: the mass flow rate of air to 3 d.p. in SI unit and privide unit symbol. Take the gas constant as 289 J/kg.K
At the beginning of the compression process in an air standard dual cycle, P1 = 1 bar and T1 = 300 K. Qin is 1000 kJ/kg.Consider compression ratio ranging from 10 to 20. Determine the work net
! Required information Problem 09.034 - Ideal Otto Cycle with Variable Specific Heats - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS An ideal Otto cycle has a compression ratio of 8. At the beginning of the compression process, air is at 95 kPa and 27°C, and 760 kJ/kg of heat is transferred to air during the constant-volume heat-addition process. Take into account the variation of specific heats with temperature. The gas constant of air is R = 0.287 kJ/kg-K. Problem 09.034.a - State After Heat Addition in Variable Heat Capacity Ideal Otto Cycle Determine the pressure and temperature at the end of the heat-addition process. (You must provide an answer before moving on to the next part.) The pressure at the end of the heat-addition process is 3915.8 kPa. The temperature at the end of the heat-addition process is 1647.7 K.