Consider a separately-excited DC motor with an armature resistance RA= 0.25 £2 and terminal voltage VT=150 V. The motor rated speed is 1800 RPM. The field winding supply VF= 36 V and the field resistance isadjustable. The motor has compensating windings and interpoles.IF (A)EA (V)Answer:0.00RPMThe speed of rotation is:0.1300.2600.40.5102115These values were taken at speed n=1800 RPM0.385If the motor is driving a load at rated armature current LA = 46 A, with Radi+RF = 90 22.Find the speed of rotation of the motor in RPM.0.60.7124 1300.8134

Given data, RA =0.25Ω VT = 150V Speed = 1800 RPM VF = 36V IA = 46A Radj + RF = 90Ω

Consider a separately-excited DC motor with an armature resistance R₁-0.25 52 and terminal voltage V₁- 150 V. The motor rated speed is 1800 RPM. The field winding supply VF= 36 V and the field resistance is adjustable. The motor has compensating windings and interpoles. IF(A) EA(V) 0.0 0 RPM Answer: The speed of rotation is: 0.1 30 0.2 60 0.4 0.5 102 115 These values were taken at speed n=1800 RPM 0.3 85 0.6 124 If the motor is driving a load at rated armature current IA 46 A, with Radi+RF-90 52. Find the speed of rotation of the motor in RPM. 0.7 130 0.8 134

Consider a separately-excited DC motor with an armature resistance R₁-0.25 52 and terminal voltage V₁- 150 V. The motor rated speed is 1800 RPM. The field winding supply VF= 36 V and the field resistance is adjustable. The motor has compensating windings and interpoles. IF(A) EA(V) 0.0 0 RPM Answer: The speed of rotation is: 0.1 30 0.2 60 0.4 0.5 102 115 These values were taken at speed n=1800 RPM 0.3 85 0.6 124 If the motor is driving a load at rated armature current IA 46 A, with Radi+RF-90 52. Find the speed of rotation of the motor in RPM. 0.7 130 0.8 134

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 6-pole, 3-phase, 60-cycle alternator has 12 slots per pole and four conductors per slot. The winding is 5/6 pitch. There are 2,500,000 maxwells (0.025 weber) entering the armature from each north pole, and this flux is sinusoidally distributed along the air gap. The armature coils are all connected in series. The winding is wye-connected. Determine the open circuit emf of the alternator.
In DC machines the number of parallel paths for a wave winding generator is Select one: O a. Three O b. Two OC. Half the number of poles O d. Equal to Number of Poles
Probl The rectangular coil in the figure below is in a field B = 0.01a,T. a. Find the torque about the z axis when the coil is in the position shown and carries a current of 10 A b. Find the torque if the coil turns through 90°7 0.2m & 0.2m 1-10A
The speed of rotation of the magnetic field for a three-phase 4-pole AC machine is 3600 rev/min. If you would like to reduce the rotation of the speed to 188.4 rad/sec what should be the number of poles in the new design? Take = 3.14 Answer:
A 50 kW induction motor is operated at a lagging power factor of 0.8, the source voltage being 230 V rms. a) Find the complex power Sm that this motor is using. b) In order to get lower electricity bill it is desired to connect a parallel compensator to the motor so as to get pf%3D0.95 lagging and still provide the 50kW real power for the motor. Determine the total complex power ST= Sm+ Sc that will achieve the desired pf, where Sc is the power of the compensator c) Determine the complex power S. of the compensator and the . value of the parallel compensator impedance. What type of circuit element should be the compensator?
An open-circuit voltage of 480 V appears across the slip-rings of a wound-rotor induction motor when the rotor is locked. The stator has 8 poles and is excited by 60 Hz source. If the rotor is driven by a variable-speed dc motor, calculate the open-circuit voltage and frequency across the slip rings if the dc motor turns a. At 500 r/min, in the same direction as the rotating field b. At 600 r/min, in the same direction as the rotating field c. At 1800 r/min, opposite to the rotating field
A 60 Hz generator is connected to a turbine operating under a head of 3000 ft with a flow of 80 cubic ft / sec. The turbine specific speed is 3 rpm and a turbine efficiency of 80%. a.) Determine the number of poles of the generator
A synchronous generator is generating 395 V at 55 Hz at a field current of 3A. The e.m.f generated when the frequency is 35HZ and the field current is 2.3A is ..............
A motor with inductance L and resistance R uses 5.0 W of power when connected to a 10-Vbattery and 400 W of power when connected to a 120-V, 60-Hz power source. Determine thevalues of R and L.
The current generated by the waterwheel generator changes direction as the wheel rotates, that is, it is an alternating current. Could you design a simple generator like this that would induce a current that continuously flowed in one direction (a DC current)? If not, explain why not. If so, describe and sketch your model solution below.
7. A coil having a resistance of 20 ohms and an inductance of 0.75 henry is connected in series with a 30-ohm resistor and to a 120-volt d-c source. A switch across the series resistor is then closed, and the circuit is assumed to be in a steady-state condition. At the instant the switch is opened, what will be the rate of current change and the power delivered by the magnetic field.