H. W.: A 35 kW induction motor has power factor 0.9 and effliciency 0.9at full-load, power factor 0.6 and efficiency 0.7 at half full-load. At noload the current is 25% of full-load current and power factor is 0.I.Capacitors are supplied to make the line power factor 0.8 at half full-load. With these capacitors in circuit, find the line power factor at: (i) fullload, and (ii) no load.

The complex power in an AC system is defined as the product of rms value of applied voltage and…

H. W.: A 35 kW induction motor has power factor 0.9 and efficiency 0.9 at full-load, power factor 0.6 and efficiency 0.7 at half full-load. At no load the current is 25% of full-load current and power factor is 0.1. Capacitors are supplied to make the line power factor 0.8 at half full- load. With these capacitors in circuit, find the line power factor at: (i) full load, and (ii) no load.

H. W.: A 35 kW induction motor has power factor 0.9 and efficiency 0.9 at full-load, power factor 0.6 and efficiency 0.7 at half full-load. At no load the current is 25% of full-load current and power factor is 0.1. Capacitors are supplied to make the line power factor 0.8 at half full- load. With these capacitors in circuit, find the line power factor at: (i) full load, and (ii) no load.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The supply frequency is not afffecting the rotor ..............of the three phase induction moto?
Please answer all subparts for like either dislike is ready Answer in short please. All subparts..
A single-phase motor is rated 5HP, 75% pf and 220V. What is the approximate size of capacitor needed to raise the nower factor to about 95%?
A 50 kW induction motor is operated at a lagging power factor of 0.8, the source voltage being 230 V rms. a) Find the complex power Sm that this motor is using. b) In order to get lower electricity bill it is desired to connect a parallel compensator to the motor so as to get pf%3D0.95 lagging and still provide the 50kW real power for the motor. Determine the total complex power ST= Sm+ Sc that will achieve the desired pf, where Sc is the power of the compensator c) Determine the complex power S. of the compensator and the . value of the parallel compensator impedance. What type of circuit element should be the compensator?
A 50 kW induction motor is operated at a lagging power factor of 0.8, the source voltage being 230 V rms. a) Find the complex power S that this motor is using b) In order to get lower electrcity bill it is desired to connecta parallel compensator to the motor so as to get pf-0.95 lagging and still provide the 50kW real power for the motor. Determine the total complex power S S+ S, that will achieve the desired pf, where Sc is the power of the compensator ) Determine the complex power S. of the compensator and the value of the parallel compensator impedance. What type of circuit element should be the compensator?
Electrical Engineering - Convargion Please solve the question quickly
Question -9b
A 240 kVA synchronous motor of rated apparent power consumes 95 kW of active power of the power grid. And it is possible to adjust it so that by working with this same active power, it compensates the power factor by providing reactive power (i.e., appearing with a capacitive component). How can you get this? What is the maximum reactive power that it can provide?
V1 = 170 V f1 = 100 Hz 1) A single-phase load has an active power of P = 2 kW at V1 V @f1Hz and the power factor is cosφ = 0.75. This motor iscompensated to cosφ = 0.85 using a parallel capacitor Find the reactive power difference between compensated and uncompensated status (which will give the capacitor power) and calculate XC and C using the power difference value?
1. An induction motor is operating near its synchronous speed. It is supplied from a 50Hz 400V (1-1) source and it has 2 poles, RR = 0.52. If the load torque is TL = 63 10-3 w² (w in rad/s), calculate speed and torque. rad Wα = 104.1 S Tm = 682.34Nm
The field windings of a series motor have a resistance of 120 ohms at 15 o C. After running for two hours, the resistance increases to 140 ohms. If the temp. coefficient at 15 deg C is -0.00427, find the temp. rise.
In Transformers: a. What is the relationship between the turns ratio and the primary to secondarycurrent ratio ? b. What is the relationship between the turns ratio and the primary and secondaryvoltage ratio? c. What can you conclude about the relationship in the values of primary andsecondary apparent power?