Load S is an Induction Motor that draws an RMS Current of 20.0 Amps at0.90 PF Lagging. Load S2 is 3.6 KVA at 0.76 PF Leading. Determine the RMS magnitude of Current I.120 VRMSS1S2O A. 40.02 Amps RMSO B. 41.07 Amps RMSOC 39.03 Amps RMSOD. 43.49 Amps RMSO E. 42.20 Amps RMS

Answered: Image /qna-images/answer/000778fa-374c-4e4b-840f-854376db175d.jpg

Answered: Determine the RMS magnitude of Current…

Engineering

Electrical Engineering

Determine the RMS magnitude of Current I.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: RMS value of sinusoidal voltage is given by Vrms= 5 V, Calculate the value of peak voltage Vm? a.…

A: In the question The RMS value of sinusoidal voltage is given by Vrms= 5 V, Calculate the value of…

Q: An industrial installation has a power factor of 0.85 in backward. The demand is 150 KVA, and the…

A: In the given questions we need to calculate the type of compensator, reactance of the compensator…

Q: 3.At the input of an installation there is a unity power factor. The installation consists of a 240…

A: For the question, the given data is not sufficient.

Q: A sinusoidal voltage having a maximum amplitude of 625 V is applied to the terminals of a 50 n…

A: Average Value of a signal: It's that steady state equivalent of a time varying signal which would…

Q: 1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and…

A: 1. Write down a formula for the three-phase power factor, assuming perfectly sinusoidal and…

Q: Given the circuit shown, answer the following questions 1 20 ww 8 Ia ww Vs 24/50 V -j40 12 in Ampere…

A: In the circuit, Find the current I2 voltage V2 The equivalent impedance in ohm.

Q: RMS value of sinusoidal voltage is given by Vrms= 5 V, Calculate the value of peak voltage Vm? a.…

A: For a sinusoidal voltage of peak value Vm and RMS value Vrms , Relation between peak value Vm and…

Q: Find the rms and average value of the wave form shown below. a. Vaverage b. Vrms

Q: Choose the % derating factor of the string which is having 8 number of SCR connected in series to…

Q: The maximum transferred average power to a load without restrictions calculated in terms of the RMS…

Q: A power station is to supply two loads. The daily load curve of the station is as shown in figure…

Q: b) A device with characteristics as shown is used to control an 110V AC supply. The load is…

A: The I-V characteristics of a device is given in the question. We need to identify the device. Also…

Q: A 50 Hz, alternating voltage of 150 V (rms) is applied independently to:

A: Vm=2Vrms =2×150Vm=212.13 V a- For purely resistive, phase angle- ϕm=0 i=Imsinwt=Im sin…

Q: Calculate the current drawn from the source with and without the capacitor connected. Determine the…

Q: An alternating current varying sinusoidally, with a frequency of 50 Hz has an rms value of 20 A.…

A: Given,For an alternating current,Frequency, f=50 HzRMS, Irms = 20 A

Q: 2. Determine the rms value for each of the waveforms shown in figure below. (a) e (V) hour 2 2 5 7…

Q: A 50 HZ Single-phase Injerter of 8o% $quare waveform output voltage supplies a 4omli with 82 from a…

A: For a single-phase inverter,f=50HzL=40mHR=8ΩVs=200V

Q: Give the rms value and the frequency in Hz of a voltage signal with value 200sin(1000t+30°) V

A: Given periodic voltage signal = 200sin(1000t+30°) V Consider the general expression of periodic…

Q: c) Figure 6 is the waveform of output voltage, vo from synchronous connection changer. The primary…

A: Solution: This is a question of 2-stage sequence control of voltage controllers. Supply Voltage (Vs)…

Q: Given the RMS value of the following 8. 32 roltage waveform is he maximum value, B, of the vayeform…

A: In the waveform Rms value of the given waveform =√(8/3) Find the value of B?

Q: The maximum transferred average power to a load without restrictions calculated in terms of the RMS…

Q: Define the steady-state error, the settling time and the rising time

Q: (m)

A: For calculation of RMS square the value which is present at the y-axis. After squaring tringle…

Q: Vs 18 V pk RL 220 N (a)

Q: In power factor correction where a motor load is normally operating with 1000 inductive vars, a…

A: It is mentioned, that in power factor correction when motor loads operate with 1000 inductive VARS…

Q: electric units a & b are connected in parallel and its rms current is 15A. If the current in b lags…

A: The solution is given below

Q: (a) The peak amplitude. (b) The peak-to-peak value. (c) The average value. (d) The rms value. (e)…

A: as per question we need to answer a,b,c we need to find peak amplitude value, peak to peak value and…

Q: If the voltage and current given below are suppliedby a source to a circuit or load, determinea. The…

A: Let the angle given be in radians. Find the complex power supplied by the source.

Q: A motor is supplied from an AC source with a voltage of 240 V-RMS. The motor is consuming an average…

Q: P.5: Write the sinusoidal expressions for voltages and currents having the following rms values at a…

A: In this question We need to write the expression of the sinusoidal waveform for voltage and current…

Q: A d.c. Buck converter operates at frequency of 2000 Hz from 200 V d.c. source supplying a 5 2…

A: It is given that:

Q: Lance Smile operated two loads in parallel. The loads draw a total of 3kW at a 90% power factor…

A: Given that Total Load (LT) = 3kW @ 0.9pf lagging Given that Load 1(L1) = 1000W @ 0.8pf lagging…

Q: A three-phase, variable-frequency drive (VFD) draws lagging non-sinusoidal line current, resulting…

A: The given question deals with spectral analysis of the non-sinusoidal line current of a three-phase…

Q: Derive the formula for the RMS value for the following

Q: When caluating the average power delivered to a bad by an AC sigre, it is not as straightforward as…

Q: Power = P = 120011. Average Resistance of heating we need to determine, element R = 1052 a. RMS…

A: Given Data:Required Data:Here, we need to determine the RMS current drawn by the kettle.Here, we…

Q: An alternating current varying sinusoidally, with a frequency of 50 Hz has an RMS value of 20 A.…

A: Given: Varying Alternating Current Sinusoidally Freq.(f) = 50 HzIRMS = 20 A

Q: A0) is supplied by an RMS value of 22o-v, 60-Hz source

Question

Load S is an Induction Motor that draws an RMS Current of 20.0 Amps at
0.90 PF Lagging. Load S2 is 3.6 KVA at 0.76 PF Leading. Determine the RMS magnitude of Current I.
120 VRMS
S1
S2
O A. 40.02 Amps RMS
O B. 41.07 Amps RMS
OC 39.03 Amps RMS
OD. 43.49 Amps RMS
O E. 42.20 Amps RMS

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Multiple Order System and Steady State Error

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A load is connected across a 25,000 Volts, 60 Hz source and draws a current of 90 A rms. If the power factor of the load is to be corrected from 0.75 lagging to 0.9 lagging, find the capacitance of the capacitor to be connected in parallel with the load.
During a lab session, the lab instructor presented the class with an alternating voltage which has a value of v=50 Sin 800t. With this material; each student was given the appropriate equipment to show that the values of the following parameters can be measured by an analyzer. Compile the correct results of the analyzer.i. The Amplitude valueii. The Frequencyiii. The Average valueiv. The RMS valuev. The Form Factorvi. The Peak Factorvii. The Instantaneous voltage when t =3 ms?
If the voltage and current supplied to a circuit orload by a source are˜VS = 170∠(−0.157) V ˜IS = 13∠0.28 Adeterminea. The power supplied by the source which isdissipated as heat or work in the circuit (load).b. The power stored in reactive components in thecircuit (load).c. The power factor angle and power factor.
A current of 10 A rms flows when a single-phasecircuit is placed across a 220-V rms source. Thecurrent lags the voltage by 60◦. Find the powerdissipated by the circuit and the power factor.
In the following circuit, find the magnitude of the current i, (mA,rms). 2002 3000 j100N I2 j1000 Sj200Q -j3000 j6000 100 Vrms ll ll +
Question-2 Can you throw the emergency solution? I would appreciate it if you write legibly.
The Subject is Basic Electrical Engineering Chapter 13. Effective Value of AC
Find the RMS Voltage and Average Voltage based from the graph
Please solve this question quickly in electric
i need the answer quickly
Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. Time remaining: 00:07:30 Electrical Engineering Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. 1- Find the phasor II, assuming that the capacitor is not connected to the circuit. Enter your answer using polar notation. Express argument in degrees. 2-Find the value of the capacitance that must be connected in parallel with the load to achieve a power factor of 100 percent. Express your answer to three significant figures and include the appropriate units. 3-Usually, power-systems engineers rate capacitances used for power-factor correction in terms of their reactive power rating. What is the rating of this capacitance in kVAR? Express your answer using three significant figures. 4-Assuming that this…