Consider a proposed new instruction named repeat. combine's a loop's condition check and counter decre instruction. For example repeat x29, loop would do the following: if (x29 > 0) { x29=x29-1; goto loop; } If this instruction were to be added to the RISC-V inst is to allow for very large loop sizes, what is the most a format? I-type S-type J-type or U-type R-type B-type

Consider a proposed new instruction named repeat. combine's a loop's condition check and counter decre instruction. For example repeat x29, loop would do the following: if (x29 > 0) { x29=x29-1; goto loop; } If this instruction were to be added to the RISC-V inst is to allow for very large loop sizes, what is the most a format? I-type S-type J-type or U-type R-type B-type

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

For the whole question, pseudo-instructions are not allowed except “j target_label”and “jr ra”. One suggestion for assembly programming problems is that you can includecomments to one or a block of instructions. Consider a RISC-V assembly function func1. func1 has three passingarguments stored in registers a0, a1 and a2, uses temporary registers t0-t3 andsaved registers s4–s10. func1 needs to call func2 and other functions may call func1also. func2 has two passing arguments stored in registers a0 and a1, respectively. Infunc1, after the program returns to func1 from func2, the code needs the originalvalues stored in registers t1 and a0 before it calls func2. (a) How many words are the stack frames of function func1?(b) Indicate which registers are stored on the stack of func1.
Using 8086 microprocessor assembly language
For example, suppose an instruction is not accepted and VA page 30 is generated. For the following use cases, a TLB controlled by software might be preferable than one handled by hardware:
For the following assembly code that is vaguely MIPS-like, trace itsexecution in both the R3000 and R4000 pipelines using a Gantt chart (ortable of some kind).LOAD R1, Memory(12340)LOAD R2, Memory(12350)ADD R3, R1, R2 // R3 = R1 + R2ADD R3, R3, R3 // R3 = R3 + R3STORE R3, Memory(12360)
We have the following C function compiled to RISC-V RV321. The following assembly sequence is equivalent to the C code snippet, but an assembly instruction is missing. what should be XXXX to have an equivalent code? int fun(char a) { fcall(); return a ^ 0x50; } fun: sp, sp,-16 ra,12(sp) s2,8(sp) s2, a0 addi SW SW mv call XXX fcall ra,12(sp) 52,8(sp) lw lw addi sp,sp, 16 jr ra O xori x10,s2,51 xori a0,s2,51 O Another instruction xori a0,s0,80 xori x10,s2,80
VDHL simple computer question.
Suppose DH contains (6B) 16 hexadecimal, AH=(CB) 16 , CF=1, and CL contains 5, What are the values of DH after the following instructions: AND DH,AH RCL DH, CL.
For example, suppose an instruction is not accepted and VA page 30 is generated. A software-managed TLB can outperform a hardware-managed TLB in the following cases:
Write down the values of destination operands and flags after the execution of each instruction: .code bh, 1 mov sub bh, 1 (а) вн 3 ? ZF = ? mov dl, o sub dl, 1 ; (b) DL = ? SF = ? mov ch, 11111111b add ch, 1 ; (c) CH = ? CF = ? al, 0 mov sub al, 1 ; (d) AL = ? CF = ? cl, 01111111b mov add cl, 1 ; (e) CL = ? OF = ? ah, 10000000b mov neg ah ; (f) CF = ? OF = ?
Consider the following MIPS code segment in the attached image, and how many iterations does this loop undergo?