Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal andvertical planes at the point are shown. Assume stress magnitudes of S- 160 MPa, S 85 MPa, and Sy- 45 MPa.Construct Mohr's circle for this state of stress on paper and use the results to answer the questions in the subsequent parts of thisGO exercise.For this Mohr's circle, point x, which represents the state of stress on the x face of the stress element, should appear:O Below and to the left of the circle center.O Belowand to the right of the circle center.O Above and to the left of the circle center.O Above and to the right of the circle center.

Draw the mohr circle Sx=-160MpaSy=-85MpaSxy=45Mpa

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of S- 160 MPa, Sy 85 MPa, and Sy-45 MPa.

Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Assume stress magnitudes of S- 160 MPa, Sy 85 MPa, and Sy-45 MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Need help. Asap pls. Thanks
Find the value of maximum principal stress if maximum shear stress is 60 MPa and minimum principal stress is 50 MPa
At a point in a stressed material, the major principal stress is 44 kPa tension and the minor principal stress is 18 kPa tension. Using Equations 1 and 2, determine the maximum shear stress that acts through the point and the normal stress on the plane of maximum shear.
50 mm Determine the stress components at point H. And show the stress state for this point on a volume cubic element given below. Cross Section 150 mm 40 mm 0.5 kN 20 mm 3 kN 160 mm 2.5 kN
Problem 05
Find principal stresses and max in plane shear stresses ...using stress transformation equation
The following stress element represents the stress state at point A of the structure in the figure below. Determine the principal stress angle in this condition. 52.8 MPa 26.4 MPa O a. 15.80 degrees O b. 30.25 degrees O. 36.15 degrees O d. 22.50 degrees
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. If 0 = 44 MPa in the direction shown, determine the principal stresses at the point. 85 MPa 56 MPa O 70.9 MPa and -97.0 MPa 82.8 MPa and -136.0 MPa 89.5 MPa and -64.2 MPa 75.1 MPa and -124.1 MPa 64.9 MPa and -105.9 MPa
Solid Mechanics
Please provide solution for this question and explanation.
Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are S, = 26 MPa, Sy= 67 MPa, and Sxy= 23 MPa. (a) Determine the principal stresses and the maximum in-plane shear stress acting at the point. (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) (c) Compute the absolute shear stress at the point. Sxy Answer: MPa (a) Op1 = op2 = MPa MPa Tmax in-plane (b) Show these stresses on an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) MPa (c) Tmax abs=
Q 3: A 60° strain rosette attached to the aluminum skin of an airplane fuselage measures the following strains in micro-meters per inch: εa = 100, εb = -200, εc = 400. If E = 10 x 106 Psi and ν = 1/3. Compute the principal stresses and maximum shear stresses and their planes.