Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an area of A1= 0.8 cm? and A2= 0.04 m2. Hydraulic oil with a specific gravity of 0.870 is pumped in as the small piston on the left side is pushed up and down, slowly raising the larger piston on the right side. A car that weighs 13,000 N is to be jacked up. F1 A2 h Hydraulic oil SG = 0.870 F2 At the beginning, when both pistons are at the same elevation (h= 0), calculate the force F1 in newtons required to hold the weight of the car.

Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an area of A1= 0.8 cm? and A2= 0.04 m2. Hydraulic oil with a specific gravity of 0.870 is pumped in as the small piston on the left side is pushed up and down, slowly raising the larger piston on the right side. A car that weighs 13,000 N is to be jacked up. F1 A2 h Hydraulic oil SG = 0.870 F2 At the beginning, when both pistons are at the same elevation (h= 0), calculate the force F1 in newtons required to hold the weight of the car.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What is the gauge reading p₂ in mm of mercury in the below figure ? The turbine develops 370 kW , when a discharge of 2 m³ / sec is flowing through it . Explain
A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of head from A to 1 is four times the velocity head in the 50mm pipe and loss of head from 2 to B is 15 times the velocity head in the 100mm pipe. The pump discharge rate us 50 liters per second. Determine the following: A. Power delivered by the pump in KW B. Pressure head at pt. 1 in meter C. Pressure head at pt 2 in meter
How to solve this question . Step-by step solution needed with explanation. ( Fill in the Blank)
The hydraulic jack in the figure is filled with two types of oil, the specific gravity of oil 2 is equal to 80% of oil 1. Neglecting the weight of the two pistons, what force F (lb) on the handle is required to support the 2000-lbf weight for this design? Take the specific gravity of oil 1 = 0.9. 6 in 3 in 2000 lbf Oil 2 Oil 1 3-in diameter in 15 in 1-in diameter F
Q 1 A
Read the question carefully and give me right solutions with clear calculations
IV. Water is discharged from a device in to air, as shown in the figure. How much is the horizontal force to hold the device. Ignore gravity and viscosity. 1 Ibf= 1 slug ft/s 2, air (2)A=0.4 t 30 fU 10 psi Flang 1/20 tis (1) A=0.8 (E) A- 0.8 n air Water density =1.94 slugs/ft^3.
1. A nurse applies a force of 4.40 N to the piston of a syringe. The piston has an area of 6.56 x 105 m². What is the pressure increase in the fluid within the syringe? kPa
Ethanol with a density of 789 kg/m moves through a constricted pipe in steady, ideal flow. At the lower point shown in the figure below, the pressure is P, = 1.90 x 10“ Pa, and the pipe diameter is 7.00 cm. At another point y = 0.35 m higher, the pressure is P, = 1.10 x 104 Pa and the pipe diameter is 3.50 cm. P (a) Find the speed of flow (in m/s) in the lower section. m/s (b) Find the speed of flow (in m/s) in the upper section. m/s (c) Find the volume flow rate (in m/s) through the pipe. |m³/s
Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter (cm) Length (m) Friction factor 1 15 500 0,02 2 10 450 0.03 3 20 800 0,025 3. Determine the flow in pipe 3.
Find the volumetric flow rate of the oil in m3/s thank you!!
Q4: A 7-cm diameter solid aluminum ball (SG = 2.7) and a solid brass ball (SG-8.5) balance nicely when submerged in a fluid as shown in figure. a) If the fluid is water, what is the diameter of the brass ball? b) If the brass ball has a diameter of 3.8 cm, what is the density of the fluid? 2 pulleys Fluid brass aluminum D= 7 cm +